manualshive.com logo in svg

National Instruments GPIB-ENET, Getting Started

Share
Download
National Instruments GPIB-ENET Getting Started Download Page 16

Chapter 1

Introduction

GPIB-ENET for Windows 95/98

1-4

©

 National Instruments Corporation

Figure 1-1 shows the seven light-emitting diodes (LEDs) on the 
GPIB-ENET top panel. The LEDs show the current status of the 
GPIB-ENET. Table 1-1 describes each LED.

Figure 1-1.  GPIB-ENET Top Panel and LEDs

Table 1-1.  LED Descriptions

LED

Indication

POWER

Indicates that power has been supplied to the unit and 
the ON/OFF switch is in the ON position.

READY

Indicates the functional state of the GPIB-ENET. 
When the GPIB-ENET is powered on, this LED 
flashes and then becomes steady when the box is 
ready for operation. Continuous flashing indicates an 
error has occurred.

TALK

Indicates that the GPIB-ENET is configured as a 
GPIB Talker.

LISTEN

Indicates that the GPIB-ENET is configured as a 
GPIB Listener.

TRANSMIT

Indicates that the GPIB-ENET is transmitting onto the 
Ethernet network.

RECEIVE

Indicates that the GPIB-ENET is receiving Ethernet 
network traffic.

LINK

Indicates that the GPIB-ENET has detected a twisted 
pair (10Base-T) link. For GPIB-ENET coax and AUI 
options, this LED is not used and remains OFF.

ETHERNET

IEEE 488 Controller

Ethernet AUI

Connector

GPIB

Connector

Location of Coax or

10Base-T Connector

(Depending on Version)

Summary of Contents for GPIB-ENET































































Reviews:

No comments

Brands by name

Popular brands

Load more brands