National Instruments FieldPoint FP-AI-100 Operating Instructions Manual Download

Page: 15 / 17

FP-AI-100 and cFP-AI-100

ni.com

Safety

This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement,
control, and laboratory use:

•

IEC 61010-1, EN 61010-1

•

UL 61010-1

•

CAN/CSA-C22.2 No. 61010-1

Note

For UL, hazardous locations, and other safety

certifications, refer to the product label, or visit

ni.com/certification

, search by model number or

product line, and click the appropriate link in the
Certification column.

Electromagnetic Compatibility

Emissions.......................................... EN 55011 Class A at 10 m

FCC Part 15A above 1 GHz

Immunity........................................... EN 61326:1997 + A2:2001,

Table 1

CE, C-Tick, and FCC Part 15 (Class A) Compliant

Note

For EMC compliance, operate this device with

shielded cabling.

CE Compliance

This product meets the essential requirements of applicable
European Directives, as amended for CE marking, as follows:

Low-Voltage Directive (safety)......... 73/23/EEC

Electromagnetic Compatibility
Directive (EMC) ............................... 89/336/EEC

Note

Refer to the Declaration of Conformity (DoC) for

this product for any additional regulatory compliance
information. To obtain the DoC for this product, visit

ni.com/certification

, search by model number or

product line, and click the appropriate link in the
Certification column.

Summary of Contents for FieldPoint FP-AI-100


















Search results

Summary of Contents for FieldPoint FP-AI-100

Reviews:

Related manuals for FieldPoint FP-AI-100

Brands by name

Popular brands

National Instruments FieldPoint FP-AI-100, Operating Instructions Manual

Search results

Summary of Contents for FieldPoint FP-AI-100

Reviews:

Related manuals for FieldPoint FP-AI-100

Brands by name

Popular brands