manualshive.com logo in svg

National Instruments FieldPoint FP-1001, Operating Instructions Manual

Share
Download
National Instruments FieldPoint FP-1001 Operating Instructions Manual Download Page 7

7

Powering the FP-1001

NOTE:  Terminal bases must be connected to the FP-1001, 
and the baud rate switch must be set, before power is applied to 
the FP-1001. 

An 11-30 VDC power supply is required by each FieldPoint stack. 
The network module filters and regulates this supplied power and 
provides power for all the I/O modules in the stack. Therefore you 
need not provide power separately to each FieldPoint I/O module 
in the stack. If your field I/O device needs to be powered 
separately, you can use the terminals provided on each terminal 
base for such power supply connections.

The power connector is a 4-pin screw terminal connector whose 
pinout is shown in Figure 7.

Figure 7.  

FP-1000 and FP-1001 Power Connector Pinout

The two terminals labeled V are internally connected on the 
network module, as are the two terminals labeled C. Power must be 
applied to one V and C pair for operation of the FieldPoint system. 
If you want to power your field I/O devices from the same power 
supply, the second V and C pair provides a convenient means of 
connecting power to the V and C terminals of a terminal base. 
Figure 7 shows this optional connection.

Specifications

Network ports ................................... 1 RS-485 port

Baud Rates ........................................ 300, 1200, 2400, 9600, 

19200, 38400, 57600, 
115200 (switch selectable)

Communication parameters .............. 1 start bit, 8 data bits, 

1 stop bit, No parity

+

–

V

V V

C C

C

To Adjacent Terminal Base

(Optional Connection)

11-30 VDC

FP1001.fm  Page 7  Thursday, July 31, 1997  8:51 AM

Summary of Contents for FieldPoint FP-1001









Reviews:

No comments

Brands by name

Popular brands

Load more brands