background image

3. Move the IP RESET and SAFE MODE switches to the OFF position.
4. Configure the IP and other network settings in MAX.

Caution

 

If the chassis is restored to the BIOS network settings, the LabVIEW

run-time engine does not load. You must reconfigure the network settings and

restart the chassis for the LabVIEW run-time engine to load.

NI 9148 Specifications

This document lists the specifications for the NI 9148 Ethernet Expansion Chassis. The

following specifications are typical for the -40 °C to 70 °C operating temperature range unless

otherwise noted.

Caution

 

Do not operate the NI 9148 in a manner not specified in this document.

Product misuse can result in a hazard. You can compromise the safety protection

built into the product if the product is damaged in any way. If the product is

damaged, return it to NI for repair.

Network

Network interface

10BaseT and 100BaseTX Ethernet

Compatibility

IEEE 802.3

Communication rates

10 Mbps, 100 Mbps, auto-negotiated

Maximum cabling distance

100 m/segment

Reconfigurable FPGA

Type

Xilinx Spartan-3 2M

Number of logic cells

46,080

Available embedded RAM

720 kbits

Power Requirements

Voltage input range

19 V to 30 V

Maximum power input

20 W maximum

Maximum power consumption

20 W maximum

Physical Characteristics

If you need to clean the NI 9148, wipe it with a dry towel.

Tip

 

For two-dimensional drawings and three-dimensional models of the NI 9148,

visit 

ni.com/dimensions

 and search by module number.

Weight (unloaded)

929 g (32.7 oz)

NI 9148 User Manual

  | 

© National Instruments

  | 

15

Summary of Contents for 9918























Reviews: