National Instruments 6008 User Manual And Specifications Download | Manualshive

Page: 5 / 27

background image

©

National Instruments Corporation

5

NI USB-6008/6009 User Guide and Specifications

Software

Software support for the NI USB-6008/6009 for Windows 2000/XP/Vista
is provided by NI-DAQmx.

The NI-DAQmx CD contains example programs that you can use to get
started programming with the NI USB-6008/6009. Refer to the

NI-DAQmx

for USB Devices Getting Started Guide

, that shipped with your device and

is also accessible from

Start»All Programs»National Instruments»

NI-DAQ

for more information.

Note

For information about non-Windows operating system support, refer to

ni.com/info

and enter

rddqld

.

LabVIEW SignalExpress for DAQ

The NI-DAQmx CD includes LabVIEW SignalExpress for DAQ which is
an interactive, measurement software tool for quickly acquiring, analyzing,
and presenting data with no programming required. The application is
available at

Start»All Programs»National Instruments»

NI DAQ»

LabVIEW

SignalExpress

.

«
...
3
4
5
6
7
...
»

Summary of Contents for 6008




























Reviews:

No comments

Related manuals for 6008

neutrino series

Brand: Xilica Audio Design Pages: 26

PARTNER Voice Messaging PC Card Release 2

Brand: Lucent Technologies Pages: 67

Brand: Belkin Pages: 72

Brand: Roland Pages: 2

Brand: Realtek Pages: 30

kontron COMe-cEL6

Brand: S&T Pages: 99

Brand: Keithley Pages: 71

Brand: Accom Pages: 15

Brand: ZyXEL Communications Pages: 215

RCO-3000 Series

Brand: C&T Solution Pages: 96

Duinotech Lilypad Plus XC3920

Brand: Jaycar Electronics Pages: 2

Brand: Galaxy Pages: 30

Brand: MA lighting Pages: 49

Brand: PADAUK Pages: 27

Brand: Renesas Pages: 4

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

Brand: ETAS Pages: 68

ControlCenter-IP 2.0

Brand: G&D Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands