National Comfort Products MADISON 1000 SERIES Installation Instructions Manual Download Page 14

National Comfort Products

539 Dunksferry Road • Bensalem, PA 19020 • (215) 244-1400 • 1-800-523-7138 • Fax: (215) 244-9579

LIMITED EXTENDED PROTECTION WARRANTY

FOR

NATIONAL COMFORT PRODUCTS (NCP) BENSALEM, PA

SPLIT-SYSTEM CONDENSING UNITS

This NCP product is warranted to be free from all manufacturing defects, material or workmanship, for a period of one year from 

the date of installation (receipt required), whether or not actual use begins on this date, or one year from the date of manufacture 

if the date of installation cannot be verified. Immediate notice to NCP will (A) provide a new or remanufactured part to replace the 

defective part, without charge for the part itself, or (B) provide a replacement unit.

National Comfort Products will not be responsible for: local transportation, removing, related service, labor, diagnosis calls, 

refrigerant, costs incurred for returning defective parts, damage or repairs required due to faulty installation or improper 

application by others, damage as a result of fire, wind, floods, lightning, accidents, or corrosive atmosphere.

EXTENDED 2ND THRU 5TH YEAR COMPRESSOR WARRANTY

If the compressor should fail because of a manufacturing defect, is in the original installation, has been operated under normal 

conditions, and is in the 2nd to 5th year following the above determined date, NCP will provide, at its option, a new or remanufac

-

tured replacement compressor.

Replacement parts are warranted for the remainder of the original product warranty, or for one year, whichever is longer. 

NCP may require that defective parts be returned to verify and identify the cause of the defect.

LIMITATION OF WARRANTIES — ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES 

OF MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH EACH 

LIMITED WARRANTY IS GIVEN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN 

IMPLIED  WARRANTY  LASTS,  SO THE ABOVE  LIMITATIONS  MAY  NOT APPLY TO YOU. THE  EX

-

PRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED, 

ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON WHATSOEVER.  

MATERIAL IS INSPECTED AT THE FACTORY AND RELEASED TO TRANSPORTATION AGENCY IN 

GOOD CONDITION.  WHEN RECEIVED, VISUAL INSPECTION MUST BE MADE IMMEDIATELY.  AP

-

PARENT SHIPPING DAMAGE SHOULD BE NOTED ON THE DELIVERY RECEIPT AND THE MATERI

-

AL INSPECTED IN THE PRESENCE OF THE CARRIER’S REPRESENTATIVE.  IF DAMAGE IS FOUND 

A CLAIM MUST BE FILED WITH THE CARRIER IMMEDIATELY.

FREIGHT DAMAGE IS NOT COVERED UNDER THIS WARRANTY.

WARNING: NO WARRANTY ON NEW UNITS INSTALLED BEHIND BRICK FACADES.  IN YEARS PAST, 

IT WAS COMMON PRACTICE TO ADD A BRICK PATTERN FACADE (PIGEON HOLES) IN FRONT OF 

THE THRU-THE-WALL UNIT TO CHANGE THE EXTERIOR APPEARANCE OF THE BUILDING.  ALL 

OBSTACLES ADDED TO IMPEDE AIR FLOW OF THE CONDENSING UNIT WILL DECREASE PER

-

FORMANCE AND CAUSE PREMATURE EQUIPMENT FAILURE AND VOID ALL WARRANTIES.  CON

-

SULT FACTORY WITH ANY QUESTIONS.

This warranty gives you specific legal rights. You may also have rights which vary from state to state.

NATIONAL COMFORT PRODUCTS, BENSALEM, PENNSYLVANIA

 

NOTE: 

All warranty parts and paper work must be submitted no later than 60 days after failure.  

Warranty requests submitted after 60 days of failure will not be processed.

14

Summary of Contents for MADISON 1000 SERIES





















Reviews: