background image

 

AA35-001 Audio Mixer Panel 

SM25 Installation and Operation Manual 

 

 

Section 2 Rev: 1.00 

Issue 4 

Page 2-3 

2.4.4.2  

Power On Checks 

Power up the aircraft’s systems and confirm normal operation of all functions of the AA35-001. Refer to 
Section 3 (Operation) for specific operational details.

 

 

a) 

Check for the correct audio output on each channel. 

 

Upon satisfactory completion of all performance checks, make all required log book entries, electrical 
load, weight and balance amendments and other documentation as required by your local regulatory 
agency before releasing the aircraft for service. 

2.5  

Adjustments and Connections 

WARNING:

 

These procedures should be performed by a qualified service 

technician, at an ESD safe workstation only.  Failure to adhere to this 

warning could cause injury to personnel and/or damage to equipment. 

2.5.1 8/600 

Ω

 Adjustment 

Remove the cover from the AA35 and locate the seven 8/600 

Ω

 adjustment jumpers (JP1 thru JP7).  

Each jumper controls one of the six independent channels or the Composite Output (refer to table 1).  
When the jumper is connected across pins A and B, the channel is set to operate with an 8 

Ω

 load 

connected.  When connected across B and C (the default setting), the channel is set to operate with a 
600 

Ω

 load connected.  Refer to the Maintenance Section of this Manual for complete details. 

 

 

Table 1: 8/600 

Ω

 Jumpers 

Jumper Channel 

JP1 Channel 

JP2 Channel 

JP3 Channel 

JP4 Channel 

JP5 Channel 

JP6 Channel 

JP7 Composite 

Output 

2.5.2 

Input Audio Level Adjustment 

The input audio level adjustment consists of six DIP switches (S1 thru S6), accessible from the right hand 
side of the AA35.  Each switch controls one of the six independent channels.  The switch number reflects 
the channel being controlled (e.g. S1 controls channel 1 and S4 controls channel 4).  Each level can be 
set to allow a 2.5 V (switch up) or a 7.5 V (switch down) input.  

2.5.3 

Composite Output Level Adjustment 

The output level of the composite audio can be adjusted from the right hand side of the AA35.  Rotating 
the trim potentiometer from fully counter clockwise to clockwise will increase the output over a 40 dB 
range. 

ENG-FORM: 805-0117.DOT 
 

CONFIDENTIAL AND PROPRIETARY TO NORTHERN AIRBORNE TECHNOLOGY LTD. 

Summary of Contents for AA35-001


















Reviews: