ASSEmbLY:
Tools required: Standard No.2 Phillips screwdriver and adjustable
wrench.
Step One:
Attach the headrest (B) to the child seat (A) using the three included
attachment screws (C). See Figure 1.
Step Two:
Attach rear rack (L) to bicycle. See Figures 2 and 3. Remove the bolts,
nuts and washers (N) from the seatpost clamp (M). Place the clamp
around the bicycle seatpost. Insert one rubber shim (T) between the
clamp and the seatpost to prevent scratching the seatpost. Install the
clamp bolts, nuts and washers, but do not fully tighten them yet.
Step Three:
Remove the threaded knobs and bolts (R) from both seat stay clamps
(Q). Fit the clamps around the bicycle seat stays and insert a rubber
shim (T) between each clamp and the bicycle frame to prevent
scratching the bicycle frame. Replace the bolts and attach the threaded
knobs, but do not fully tighten them yet.
Step Four:
Adjust the position of the seatpost and seat stay clamps until the top
surface of the rack is level (parallel to the ground). Once the rack is
level, securely tighten all the attachment hardware:
1. Securely tighten the four bolts (P) that attach the seatpost clamp to the rack.
2. Securely tighten the seatpost clamp hinge bolt (O).
3. Securely tighten both seatpost clamp bolts (N).
4. Securely tighten the two bolts (S) that attach the seat stay clamps to the rack.
5. Securely tighten both seat stay clamp knobs (R).
INSTALLATION:
Step One:
Attach the child seat to the rear rack. Loosen the red knob (I) on top of the locking lid (H) and lift the lid.
See Figure 4. Remove the pin clip (K) from the end of the red safety bar (J) on the underside of the seat and remove
the safety bar. See Figure 5.
Step Two:
Position the front of the child seat at the rear of the rack and slide the seat forward onto the rack. As you slide the seat forward, make sure the rails of the
rack are positioned inside the tabs on the underside of the seat. See Figure 6.
Step Three:
Slide the seat forward until the stop tab on the back of the seat contacts the rear of the rack and the positioning tab at the front of the seat is forward of the
crossbar at the front of the rack. See Figures 4 and 6.
Step Four:
Close the locking lid (H) and firmly tighten the red knob (I). Pull up on the lid to make sure it is locked. You should not be able to open the lid once the knob
is tightened.
Step Five:
Insert the red safety bar (J) on the underside of the seat and install the pin clip (K) in the end of the safety bar. See Figure 5. Make sure the seat is secure on
the rack by trying to move it side to side and front to back. If properly attached, the seat should not move.
USING THE CHILD SEAT:
Step One:
Unbuckle the seat harness and raise the grab handle by releasing the tab on the left side of the seat and lifting the handle.
Step Two:
Place the child in the seat, buckle the harness and adjust the straps for a snug fit. Close the grab handle and make sure the tab at the end of the handle is
fully engaged (it should clip over the edge of the seat).
Step Three:
Adjust the position of the foot stirrups and leg straps. Open the cam lever on the back of each foot stirrup (see Figure 5) and raise or lower the stirrup to the
desired position (this will be easier if the leg straps are opened). Once the stirrups are positioned correctly, close the cam levers. Note that the leg straps can
also be positioned higher or lower by using the upper or lower positioning slots.
REmEmbER:
1. Before each use, check to ensure all rack mounting hardware is securely tightened and that the seat is securely attached to the rack.
2. Rider and passenger should always wear properly fitting helmets.
Ride safely and enjoy your Nashbar™ Deluxe Child Seat!
PARTS LIST:
Part Part Code Quantity
Molded Seat with Seatback Pad & Seat Cushion ............. A ........................1
Headrest .................................................................................. B ........................1
Headrest Mounting Screws.................................................. C ........................3
Grab Handle ........................................................................... D ........................1
Seat Harness .......................................................................... E.........................1
Leg Straps ............................................................................... F .........................2
Foot Stirrups ...........................................................................G ........................2
Locking Lid ............................................................................. H ........................1
Lid Knob ...................................................................................I .........................1
Safety Bar ............................................................................... J .........................1
Pin Clip .................................................................................... K ........................1
Rear Rack ................................................................................ L .........................1
Seatpost Clamp......................................................................M ........................1
Seatpost Clamp Bolts, Locknuts & Lockwashers ..............N .............. 2 each
Seatpost Clamp hinge Bolt, Locknut & Lockwasher ........O .............. 1 each
Seatpost Clamp attachment Bolts, Nuts & Washers ........ P............... 4 each
Seat Stay Clamps ..................................................................Q ........................2
Seat Stay Clamp Bolts & Knobs .......................................... R .............. 2 each
Seat Stay Clamp attachment Bolts & Nuts ........................ S .............. 2 each
Rubber Shims ........................................................................ T.........................3
Fig 6
Rack
Rail
Stop
Tab
Seat
Tab
