Nash Elmo G 400 Series Operating Instructions Manual Download Page 5

 
 

 

 

 

nash_elmo Industries GmbH 

5 / 23 

 

Order No.: 610.44436.40.000 

Subject to change 

 

 

Edition 09/2003 

 

Safety

 

  WARNING 

Danger from rotating impeller: 
Cutting/cutting off of extremities! 

The rotating impeller is accessible with the inlet 
and discharge connections open! 
Do not reach into the unit through open 
connections! 
Do not insert objects into the unit through the 
openings! 

 

 

  WARNING 

Danger from rotating impeller: 
Cutting/cutting off of extremities! 

The rotating impeller is accessible with the inlet 
and discharge connections open! 
With free entry and exit of gases, i.e. with 
direct intake out of or direct feeding into the 
atmosphere without piping, the following 
therefore applies: 
Provide the inlet and discharge connections of 
the pump-motor unit either with additional 
mufflers or with additional piping of a sufficient 
length to prevent access to the impeller! 

 

 

  WARNING 

Danger of burns from hot surfaces of the 
pump-motor unit and from hot fluids! 

High temperatures of up to approx. 160 °C 
[320 °F] can occur on the surface of the pump-
motor unit. 
Cover the pump-motor unit with a suitable 
touch protection (e.g. perforated plate cover or 
wire cover). 
Do not touch during operation! 
Allow to cool after shut-down! 

 

1.3 Residual 

risks 

 

  WARNING 

Danger zone: 

Hot surface up to approx. 160 °C [320 °F]. 

Hazard: 

Possible burns. 

Protective measures: 

Cover the pump-motor unit with a suitable 
touch protection (e.g. perforated plate cover or 
wire cover). 

 

 

  WARNING 

Danger zone: 

Fan guard 

Hazard: 

Long, loose hair can be drawn into external fan 
through fan guard grate, even with fan guard 
mounted! 

Protective measures: 

Wear hair net! 

 

 

  WARNING 

Danger zone: 

Missing or defective muffler inlet or discharge 
connection. 

Hazard: 

Possible serious hearing damage due to 
emitted noise. 

Protective measures: 

Have missing or defective mufflers replaced. 
Conduct a noise measurement in the system 
after installing the pump-motor unit.  
The following measures must be taken by the 
operator: 

• 

from 85 dB(A): 

– 

Hearing protection must be provided. 

• 

from 90 dB(A): 

– 

Mark noise area with a warning sign. 

– 

Wear hearing protection. 

 

 

  WARNING 

Danger zone: 

Environment of pump-motor unit. 

Hazard: 

Possible serious hearing damage due to 
emitted noise. 

Protective measures: 

Conduct a noise measurement in the system 
during operation after installing the pump-
motor unit. 
The following measures must be taken by the 
operator: 

• 

from 85 dB(A): 

– 

Hearing protection must be provided. 

• 

from 90 dB(A): 

– 

Mark noise area with a warning sign. 

– 

Wear hearing protection. 

– 

With free entry and exit of gases, i.e. 
with direct intake out of or direct feeding 
into the atmosphere without piping, 
attach an additional muffler. 

 
 

Summary of Contents for G 400 Series
























Reviews: