manualshive.com logo in svg

Nasco Lifeform LF01121U, Instruction Manual

Share
Download
Nasco Lifeform LF01121U Instruction Manual Download Page 6

6

6

B.  IV Injection and Withdrawal

1.

  Start with a fully pressurized 

arm. See procedure A under 

General Instructions for Use.

2.

  Close the clamp on Fluid  

   Supply Bag B.

3.

  Open the clamp on Fluid  

   Supply Bag A.
The arm is now ready to perform injections or withdrawals along any 

of the 8 fluid lines present in the arm. Nasco recommends the use of 

small diameter needles for these procedures; 20 to 25 gauge. Use 

only distilled water to prep the injection sites and as an injection. A 

realistic flashback will occur when the vein has been properly punc-

tured. 

(See Figure 7)

C. Intravenous 

     Infusions

1.

  Begin with a fully  

   pressurized arm.  

   See procedure A  

   under General  

 

   Instructions for  

   Use.

2.

  Select the appro- 

   priate intravenous  

   infusion needles  

   or butterfly  

   included. Nasco  

   recommends  

   small gauge  

   needles 20-25  

   gauge.

3.

  Make sure the  

   arm is palm down  

   and the clamps on Bags A and B are closed.

4.

  Simulate cleansing the injection site with distilled water.

5.

  Insert the IV needle or butterfly into a vein. Flashback will indicate  

   proper insertion.

6.

  Attach the needle or butterfly to the tubing from the infusion solution  

   (not supplied) or fluid supply bag C (sold separately) with the latex  

   adapter if needed. 

(See Figure 8 and inset.)

7.

  Open the clamps on fluid supply bag B. 

B.  IV Injection and Withdrawal

1.

  Start with a fully pressurized 

arm. See procedure A under 

General Instructions for Use.

2.

  Close the clamp on Fluid  

   Supply Bag B.

3.

  Open the clamp on Fluid  

   Supply Bag A.
The arm is now ready to perform injections or withdrawals along any 

of the 8 fluid lines present in the arm. Nasco recommends the use of 

small diameter needles for these procedures; 20 to 25 gauge. Use 

only distilled water to prep the injection sites and as an injection. A 

realistic flashback will occur when the vein has been properly punc-

tured. 

(See Figure 7)

C. Intravenous 

     Infusions

1.

  Begin with a fully  

   pressurized arm.  

   See procedure A  

   under General  

 

   Instructions for  

   Use.

2.

  Select the appro- 

   priate intravenous  

   infusion needles  

   or butterfly  

   included. Nasco  

   recommends  

   small gauge  

   needles 20-25  

   gauge.

3.

  Make sure the  

   arm is palm down  

   and the clamps on Bags A and B are closed.

4.

  Simulate cleansing the injection site with distilled water.

5.

  Insert the IV needle or butterfly into a vein. Flashback will indicate  

   proper insertion.

6.

  Attach the needle or butterfly to the tubing from the infusion solution  

   (not supplied) or fluid supply bag C (sold separately) with the latex  

   adapter if needed. 

(See Figure 8 and inset.)

7.

  Open the clamps on fluid supply bag B. 

Figure 7

Figure 7

Figure 8

Figure 8

A.

A.

C.

C.

B.

B.

NP097_95_LF01121U_LF01126U_AdvancedInjectionArm.indd   6

12/19/14   3:29 PM

Summary of Contents for Lifeform LF01121U













Reviews:

No comments

Brands by name

Popular brands

Load more brands