background image

BMA SERIES: INSTALLATION & OPERATION MANUAL

PAGE 2

The inDESIGN BMA 30, BMA 60, BMA 120 and BMA 240 
are high quality mixer amplifiers for commercial and industrial 
audio applications.

The BMA series feature 4 Mic/line inputs. Microphone input 1 
features a mute so that a Microphone on this channel will mute 
all other inputs, useful for paging announcements. The BMA 
Series provide either 4 Ohm or constant voltage 100V speaker 
outputs. A pre-amp out/power amp in link allows for the mixer 
audio signal to be sent to an external equaliser or a booster 
amplifier. Shipped with a link fitted.

The mixer amplifiers are part of inDESIGN’s Install Series, which 
also includes mixers and power amplifiers. These units provide 
excellent features and value.

INTRODUCTION

INTRODUCTION  

2

IMPORTANT SAFETY 
INSTRUCTIONS   3

INSTALLATION   5

FRONT PANEL 

 

6

REAR PANEL 

 

7

BLOCK DIAGRAM: 
•  Input 

 

 

•  Mix  

 

 

•  BMA 30/60 

        10 

•  BMA 120/240          11

SPECIFICATIONS          12

CONTENTS

Electrical and Safety Warnings

THESE SERVICE INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. 

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING 

OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS 

UNLESS YOU ARE QUALIFIED TO DO SO.

CAUTION

The lightening flash with arrowhead 

symbol, with an equilateral triangle, 

is intended to alert the user to the 

presence of un-insulated 

“dangerous voltage” within the products 

enclosure that may be of sufficient 

magnitude to constitute a risk of electric 

shock to persons.

WARNING: TO REDUCE THE RISK OF ELECTRIC 

SHOCK, DO NOT REMOVE COVER (OR BACK). 

NO USER SERVICEABLE PARTS INSIDE. REFER 

SERVICING TO QUALIFIED SERVICE PERSONNEL. 

AVERTISSEMENT: POUR ÈVITER 

LE RISQUE D´INCENDIE OU DE CHOCS 

ÈLECTRIQUES, NE PAS EXPOSER CET APPAREIL À 

LA PLUIE OU À L´HUMIDITÈ

The exclamation point within an 

equilateral triangle is intended to 

alert the user to the presence of 

important operating and maintenance 

(servicing) instructions in the literature 

accompanying the appliance.

Summary of Contents for BMA 30













Reviews: