background image

W415-2348 / B / 01.22.20

EN

2

  

safety information

• 

This appliance is hot when operated and 
can cause severe burns if contacted.

• 

Any changes or alterations to this 
appliance or its controls can be 
dangerous and is prohibited.

• 

Do not operate appliance before reading and 

understanding operating instructions. Failure 

to operate appliance according to operating 

instructions could cause fi re or injury.

• 

Ensure the glass door is opened or removed 

when lighting the pilot for the fi rst time and 

when the gas supply has run out.

• 

Risk of fi re or asphyxiation, do not operate 

appliance with fi xed glass removed and never 

obstruct the front opening of the appliance.  

• 

Do not connect 110 volts to the control valve, 

with the exception of models; GSST8 and 

GT8.

• 

Risk of burns. The appliance should be turned off and cooled before servicing.

• 

Do not install damaged, incomplete or substitute components.

• 

Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during 

installation. Sheet metal edges may be sharp.

• 

Do not burn wood or other materials in this appliance.

• 

Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing 

and operating the appliance. 

• 

High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at 

test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test 

pressures equal to or less than 1/2 psig (35mb).

• 

The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance 

to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these 

appliances are suitable for 0°F / -18°C.

• 

Children and adults should be alerted to hazards of high surface temperature and should stay 
away to avoid burns or clothing ignition.  

• 

Young children should be carefully supervised when they are in the same room as the 
appliance. Toddlers, young children and others may be susceptible to accidental contact 
burns. A physical barrier is recommended if there are at risk individuals in the house. To 
restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers, 
young children and other at risk individuals out of the room and away from hot surfaces.

• 

Clothing or other fl ammable material should not be placed on or near the appliance.

• 

Due to high temperatures, the appliance should be located out of traffi c and away from 
furniture and draperies.

• 

Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.

• 

Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot 

surfaces.

• 

Even after the appliance is off, it will remain hot for an extended period of time.

• 

Check with your local hearth specialty dealer for safety screens and hearth guards to protect children 

from hot surfaces. These screens and guards must be fastened to the fl oor.

• 

Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior 
to operating the appliance.

• 

It is imperative that the control compartments, burners and circulating blower and its passageway in the 

appliance and venting system are kept clean. The appliance and its venting system should be inspected 

before use and at least annually by a qualifi ed service person. More frequent cleaning may be required 

due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and 

free from combustible materials, gasoline and other fl ammable vapors and liquids.

• 

If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it 

serviced. Keep burner and control compartment clean. 

• 

Under no circumstances should this appliance be modifi ed.

• 

Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner fl ame 

patterns.

HOT GLASS WILL CAUSE 

BURNS.

DO NOT TOUCH GLASS UNTIL 

COOLED.

NEVER ALLOW CHILDREN TO 

TOUCH GLASS.

!

DANGER

A barrier designed to reduce the risk of burns from the 
hot viewing glass is provided with this appliance and 
shall be installed for the protection of children and other 
at-risk individuals.

!

WARNING

Summary of Contents for Havelock GDS50-1NSB













































































































Reviews: