TRANSMITTER WALL MOUNT:
Secure to the desired wall location using
screws, and anchors if required.
RECEIVER OPERATION:
The receiver switch must be in the
TRANSMITTER
position for the
transmitter to function.
F-50 THERMOSTATIC FUNCTION:
Thermostatic control automatically cycles the fi replace on and off to
maintain the desired room temperature.
To turn the fi replace burner on, press the
(ON/OFF) button.
The LCD will display the word “ON” and the fl ame indicator will be
shaded in.
The
(ON/OFF) button is used to turn the fi replace on or off
only. It does not set temperature.
The
(THERMOSTAT) button is used to control room
temperature. Once pushed, “ON” lights up next to the thermostat
bulb located in the top left corner of the LCD screen.
Set desired room temperature using the
(UP) and
(DOWN) buttons. If the temperature of the room exceeds the
desired room temperature, the thermostat will automatically turn
the fi replace “OFF”.
CAUTION: In the event that the transmitter fails to send a
signal to the receiver for a period of twenty-four hours, the
receiver will automatically turn OFF the fi replace. This may
occur if the set temperature is not reached, if the transmitter is
out of range (25 feet), or if the transmitter batteries fail.
The twenty-four hour safety timer allows the receiver to
assume control of the fi replace after two hours of uninterrupted
operation. After two hours of continuous operation by the
fi replace the receiver will cycle OFF for 30 minutes and ON for
20 minutes for the next four hours.
If a signal has not been received after twenty-four hours the
receiver will shut OFF the fi replace. Press the AUTO ON/OFF
button on the transmitter to reset the transmitter, then press
the AUTO ON/OFF button again to resume operation.
The six hour safety timer may be disengaged by moving the
toggle switch on the back of the receiver. Factory setting
is ON. Changing the switch will allow the fi replace to run
continuously if required.
WARNING: In the event of prolonged absences, the F-50
should not be left in thermostat mode. If the transmitter
batteries fail while the fi replace is operating the receiver will
assume control and shut OFF the fi replace after twenty-four
hours. If the transmitter batteries fail while the fi replace is not
operating the fi replace will remain OFF.
TEMPERATURE FUNCTION:
Remove the battery cover on the back
of the transmitter to expose the °C/°F
dip switch. Move the dip switch to your
desired temperature mode.
Selected mode will appear in the right
corner beside the room temperature.
CHILD-PROOF FUNCTION:
1.
Remove the battery cover at the
back of the transmitter to expose the
child-proof dip switch.
2.
Slide the child-proof dip switch
to position marked C/P to activate the
child-proof function. A lock symbol will
appear in the bottom left corner when
the child-proof function is activated.
3.
In child-proof mode the transmitter will not operate the Receiver
until the switch is returned to the other position.
BATTERIES:
The transmitter uses 2 AAA batteries. The receiver uses 4 AA
batteries. Batteries should be replaced at least every 6 months or
when the low battery indicator is lit on the receiver or the transmitter
LCD.
Use alkaline batteries only.
TO CHANGE BATTERIES:
Receiver: Slide the switch to OFF. Press the battery compartment
slightly into the receiver and release enabling the battery
compartment to pop out. After removing the original batteries, wait
at least 1 minute before replacing with fresh batteries.
Transmitter: Gently press and slide the battery cover from the
rear surface of the transmitter. After removing
the original batteries, wait at least 1 minute before
replacing with fresh batteries.
LCD
DISPLAY
ON / OFF
BUTTON
THERMOSTAT
BUTTON
UP
BUTTON
DOWN
BUTTON
AAA
AAA
°F
°C
C/P
BATTERY COVER
W415-0628 / 11.20.07
TRANSMITTER
REVIEW VIEW
FLAME
INDICATOR
LOW
BATTERY
INDICATOR
THERMOSTAT
BULB
SIGNAL
INDICATOR
