manualshive.com logo in svg

NAPCO XP-600 - 9-16-1997, User Manual, Page: 13 / 16

Share
Download
NAPCO XP-600 - 9-16-1997 User Manual Download Page 13

13

9

System Troubles

Keypad Beeps or

9

9

SYSTEM  Flashes

Zone light

ON

System Trouble

Condition

Action

2 

Beeps

2

Fire Trouble

A  problem has  been detected in the Fire Circuit.
Call installing company for service.

2

 Beeps

3

Wireless Receiver
Trouble

A problem has been detected with the  wireless receiver.
Call installing company for service.

2 

Beeps

4

Wireless Receiver
Jam

A problem has been detected with a wireless receiver.
Call installing company for service.

3 

Beeps

1-6

Wireless
Transmitter Low
Battery

The battery in a wireless transmitter is low and should be re-
placed. This transmitter  is on the zone corresponding to the num-
ber of the lit zone light. The replacement battery for the GEM-
Trans2 door/window transmitter, GEM-PIR motion detector and
GEM-GB glass break detector is the Duracell DL123A.  (2 re-
quired for the GEM-PIR and GEM-GB.) The GEM-DT Dual Tech-
nology Sensor requires C-Cell Duracell MN1400 batteries(4).
Warning: Replace batteries only with the same type as specified
above. Use of another battery may present a risk of fire or explosion.
Do not recharge or disassemble battery, or dispose of in fire.

4

 Beeps

1-6

Wireless
Transmitter
Supervisory Failure

A problem has been detected with a wireless transmitter.
Call installing company for service

5 

Beeps

1-4

Wireless Smoke
Detector Low Bat-
tery

The battery in a wireless smoke detector is low and should be
replaced.  This wireless smoke detector should be marked with a
number corresponding to the number of the lit zone light.  The
replacement batteries required are Duracell 9 Volt Alkaline (2).
Warning: Replace batteries only with the same type as specified
above. Use of another battery may present a risk of fire or explosion.
Do not recharge or disassemble battery, or dispose of in fire.

6 

Beeps

1-4

Wireless Smoke
Detector Supervi-
sory Failure

A problem has been detected with a wireless smoke detector.
Call installing company for service.

7 

Beeps

1-6

Zone Trouble

Call installing company for service.

FIRE

AC

    SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 5

ZONE 6

ZONE 4

 ARMED

Oi218a 
page 13

Tuesday, September 16, 1997 08:28 

Summary of Contents for XP-600 - 9-16-1997

















Reviews:

No comments