background image

Special Functions  

A

By pressing 

followed by  the appropriate key, (do not press simultaneously) these special functions and features

can be enabled:

A0 

Easy Arm 

 (when system is disarmed)

 

The Easy Arm feature allows the system to be armed by 
pressing 

followed by 

0

. This will allow the easy 

arming  of the system by someone who is not a regular 
system  user.

a0

Easy Exit 

 (when system is armed)

This function (if programmed) allows an occupant to leave 
the  premises without disarming the system. Pressing 

followed by 

while the system is armed will start a 3 

minute period, during which you can leave through the 
Exit/ Entry door.

A1

Bell / Battery Test

  Pressing 

followed by 

1

 will cause the bell, or siren

to

sound for 2 seconds. This will also initiate a test of your 
battery to make sure it is adequately charged. The XP-400 
also performs an automatic battery test very 24 hours

A3

Access Output

   If programmed, pressing 

followed by 

will activate 

the  Access Output which may be configured to open a 
door  strike, turn on lighting, or activate some other special 

fea ture your installer has provided.

A4

Instant Mode

   Pressing 

A

 followed by 

4

 will cancel the Entry delay 

and put the system into the “Instant” mode. This  is  typic-
ally done in the evening when all family members are home 
for the night. When the system is disarmed, the Instant 
mode will be canceled.

A5

Chime Mode  On / Off

   Pressing 

A

 followed by 

will activate / deactivate the

door chime.  Activating this feature will cause any door   
to beep the keypad sounder when it is opened.

A8

Program Mode

  Pressing 

A

 followed by 

8

 will enable the “Program 

Mode”, which will allow you to program and erase user 
codes. (see Programming user codes, page 14)

A9

Kepad Sounder  On / Off

  Pressing 

A

 followed by 

9

 will deactivate / activate  the 

keypad sounder, depending on its present state. By
activating sleep mode on a keypad installed in a bedroom, 
for example, you effectively turn off that keypad’s sounder.  
However, any other  keypads  on the system will still sound 

10

Oi220a.pub 
page 10

Thursday, December 18, 1997 18:31 

Summary of Contents for XP-400

















Reviews: