background image

20 

StarLink

 SLE Commercial Series Alarm Communicators -- Installation Instructions 

Input Configuration Options 

Option

 

Armed 

Disarmed 

Resend 

TBL every 

24 Hrs.  

NOC Inputs 

"Function" 

Selection 

Comments  

Cut 

Wire* 

Open  Short 

Cut 

Wire* 

Open  Short 

FACP 

with

 DACT 

Use IN2 or IN3 only for trouble.  

Panel reports via dialer capture, 

but Linecut reports via an input 

on radio.  

TBL 

TBL 

TBL 

Yes 

Supervised Fire 

Trouble (Linecut) 

Requires two EOLRs.  Radio 

reports in CID.   

FACP 

with

 DACT 

Use IN1 (not supervised) either 
for trouble 

or

 alarm.  Panel has 

trouble (or alarm) relay that 

closes on the condition. 

TBL  

(or 

ALARM) 

Yes 

Un-Supervised 

Fire Trouble (use 

'User Defined' 

selection for 

Alarms) 

Non-supervised (use conduit 

activation re12V) 

FACP 

without

 DACT 

Use IN2 or IN3 for both Alarm 

and Trouble on one input.  

Panel has alarm and trouble 

relay outputs. 

TBL 

TBL 

ALARM 

Yes 

Supervised Fire 

Alarm/Trouble 

Requires two EOLRs.  The 

Trouble relay N.C. contact 

(energized opens) is put in 

series with one ELOR.  Alarm 

relay put across both EOLR 

and trouble relay. 

BURG 

with

 DACT 

Use IN2 or IN3 for only trouble 

reporting.  Panel reports via 

dialer capture but Linecut re-

ports via an input on radio. 

ALARM 

ALARM  ALARM 

TBL 

TBL 

TBL 

No 

Supervised Burg-

Linecut 

Requires two EOLRs.  Pro-
gram panel to report Open/

Close (radio remembers last 

state of panel for Napco panels 
when used with local download 

cable).   

BURG 

without

 DACT 

Use IN2 or IN3 for both Alarm 
and Trouble. Panel has alarm 

and Trouble Relay/PGM out-

puts. Two EOLRs are needed 

since for UL Burg it is required 
to detect both wire breaks and 

shorts. 

ALARM 

TBL 

ALARM 

TBL 

TBL 

TBL 

No 

Supervised Burg 

Alarm/Trouble 

Requires two 10K EOLRs.  

Three off normal conditions 

can be detected, namely, cut 

wire, shorted loop and one of 

the EOLR's having a closed 

contact in series.  The Trouble 

relay N.C. contact (energized 

opens) is put in series with one 

ELOR. The Alarm relay N.O. 

contact is put across both 

EOLRs and trouble relay. The 

panel Armed or Disarmed state 

is determined by a separate 

input (see Option 6 in this table 

below for armed status opera-

tion). (

Note: 

 The Alarm relay 

should NOT activate on 24hr 

zones.) 

BURG

 without

 DACT: 

Armed 

Status

 

Use IN2 or IN3 for Armed Sta-

tus input. Two EOLRs are 

needed since for UL Burg it's 

required to supervise for both 

wire breaks and shorts. 

TAMPER 

ALARM 

N/A 

ALARM 

TBL 

N/A 

TBL 

No 

Supervised Arm/

Disarm Status 

Requires two 10K EOLRs. A 

relay or PGM for Arm/Disarm 

status goes in series with one 

EOLR where open is disarmed 

and closed is armed. The other 

EOLR is across the series 

combination (relay for Arm/

Disarm and first ELOR) to 

provide the loop supervision. 

Application 

*Note:  On line cut, PGM1 will activate.   

Summary of Contents for StarLink SLE

























Reviews: