background image

StarLink

 SLE-LTE Commercial Series Alarm Communicators -- Installation Instructions 

 

armed condition, any loss of communication must be 
treated as a Burglary Alarm at the Central Station.

  

 

The following models are available: 

 

SLE-LTEV-CFB-PS

:  Commercial / Residential Fire and 

Burglary Radio in red metal housing with SLE-ULPS-R 
power supply and 16.5V / 20VA transformer mounted 
inside housing 

SLE-LTEV-CB-TF

:  Commercial / Residential Burglary 

and Residential Fire Radio in white metal housing with 
SLE-ULPS-R power supply and TRF12/T123 plug-in 
16.5V / 20VA transformer 

SLE-LTEV-CFB

:  Commercial / Residential Fire and Bur-

glary in red metal housing.  Powered directly from control 
panel (no power supply, no transformer, rated 12/24VDC 
input) 

SLE-LTEV-CB

:  Commercial / Residential Burglary and 

Residential Fire Radio in white metal housing.  Powered 
directly from control panel (no power supply, no trans-
former) 

 

 

The following features are included with models that include 
a SLE-ULPS-R power supply:   

 



Power limited output to the StarLink radio PC board 12V 
input terminals 



Battery connection red and black flying leads 



Monitored battery charging and Active battery test circuits 



StarLink radio trouble input (from StarLink radio PC board 

PGM1 

terminal to detect StarLink radio trouble) 



Requires a sealed lead acid min 4AH / max 7AH battery 
for minimum 24-hour standby time (max charge current 
200mA). 



Trouble relay output (

C

N/O 

and 

N/C

 terminals) to wire 

to a panel zone dedicated to "LTE Trouble" (dry con-
tacts).  Remove jumper "

J2

" to isolate common from 

ground 



Green 

AC ON 

LED visible from the exterior housing 



Yellow 

TROUBLE 

LED on PC board.  Flashes signify: 

 

One flash: AC fail / brownout (2 hour delay) 
Two flashes: Low battery 
Three flashes: Charging circuit trouble 
Four flashes: StarLink radio trouble 

 

 

The housing-mounted transformer (when provided) is mount-

StarLink™ SLE-LTE Commercial Series  

Alarm Communicators  

INSTALLATION INSTRUCTIONS 

WI2226ALF  8/18 

333 Bayview Avenue 

Amityville, New York 11701 

For Sales and Repairs, (800) 645-9445 

For Technical Service, (800) 645-9440 or visit us at 

http://tech.napcosecurity.com/ 

(Note:  Technical Service is for security professionals only)

 

Publicly traded on NASDAQ      Symbol: NSSC 

© NAPCO 2018 

INTRODUCTION 

 The 

StarLink

 Commercial / Residential Fire and Burglary 

alarm capture radio communicators are fully supervised, 
wireless digital two-way subscriber units supported by an 
extensive nationwide wireless network.  All models are 
compatible with most 12VDC alarm control panels (always 
adhere to the documentation provided by the control panel 
manufacturer).  Model 

SLE-LTEV-CFB 

is compatible with 

most 12 or 24VDC control panels.  All can function as a 
backup to existing telephone lines, or as sole path primary 
communicators.  In backup mode, all units will automatical-
ly switch the communication channel from the telephone 
line to the network when telephone line trouble is detected.  

See WI2140 for programming information.   

  The SLE-LTE Series radios use data-capture technology 

that captures the alarm report from the control panel and 
transmits the alarm signals to the SLE Control Center; the 
alarm signals are then forwarded to ANY central station via 
Contact ID or Sur-Gard System II or Sur-Gard System V 
central station receivers via TCP/IP using standard line 
security.  The SLE Control Center reports a trouble signal 
in the event that the network does not receive the expected 
supervision signal from the wireless communicator.  

 

For Commercial Burglary installations, under the 

(

 

(

 

(

 

(

 

(

 

(

 

(

 

(

 

(

 (     ) 

)

 

)

 

)

 

)

 

)

 

)

 

)

 

)

 

)

 

(1) 

(2) 

Control 
Panel 

Network  

Operator 

UL Classified StarLink Network  

Operations Center 

(3) 

CENTRAL 

STATION 

(5) 

(4) 

STARLINK RADIO REPORTING PATH 

 

The diagram below shows the transmission path of a 
signal from the StarLink radio to the central station.   

 

1. 

Signal from a Control Panel.  

 

2. 

StarLink

 radio receives the signal transmission 

(from the TIP an RING wires); sends RF signal 
through the network operator.  

3. 

Network Operator

, part of the vendor system, a 

section of the cellular spectrum.   

4. 

SLE Control Center

, receives and routes data. 

5. 

Central Station

StarLink 

Radio 

AGENCY LISTINGS 



UL 864 Standard For Control Units and Accessories For 
Fire Alarm Systems, 10th Edition 



UL 1610 Standard For Central-Station Burglar-Alarm Units 



UL 985 Standard For Household Fire Warning System Units 



UL 1023 Standard For Household Burglar-Alarm System 
Units 

LTEV models are 

Verizon

®

 Network Certified

 

Summary of Contents for SLE-LTEV-CB





















Reviews: