background image

nitrogen gas generator

1.1  general information

This manual is copyrighted, all rights reserved. It may not, in whole or in part, be copied, photocopied, reproduced, 
translated, or reduced to any electronic medium or machine readable form without prior consent in writing from 

nano purification solutions ltd. It may not be distributed through the internet or computer bulletin board systems without 
prior consent from nano purification solutions ltd.

©2021 Air and Gas Solutions LLC.

range:  

GEN2 i4.0 PSA nitrogen gas generators 

models:  

GEN2- 1110, 2110, 3110, 2130, 3130, 4130, 6130, 8130, 10130 & 12130

doc no: 

17-100-0145

issue:  

2022-059

1.2  manufacturers details and support

nano-purification solutions ltd.

 

(Manufacturer)

 

address: 

 

Dukesway,  

 

 

Team Valley Trading Estate 

  Gateshead 

 

  NE11 

0PZ

  United 

Kingdom

 

telephone:

 

+44 (0) 191 497 7700

 

internet:

 

 

www.n-psi.co.uk

 

e-mail:

  

[email protected]

 

nano-purification solutions inc.

 

address: 

 

509 David Cox Road

  

  

Charlotte, NC 28269 

 

  USA

 

telephone:

 

+1 (704) 897-2182

 

 

internet:

 

 

www.n-psi.com

 

 

e-mail:

  

[email protected]

 

 

nano-purification solutions inc.

 

address: 

 

7 Petrie Street 

  St. 

Catharines, 

  Ontario 

 

  L2P 

3J6 

  Canada

 

telephone:

 

+1 (905) 684-6266

   

internet: 

 

www.n-psi.com

   

e-mail:

  

[email protected]

 

nano-purification solutions GmbH

 

address:  

Maastrichter Straße 12

 

 

D-41812  Erkelenz

  Germany

 

telephone:

 

+49 2151 4828 418 

 

internet:

  

www.n-psi.de

 

 

e-mail:

  

[email protected]

NOTES: highlight important sections of information where 
particular care and attention should be paid.

CAUTIONS

:  indicate any situation or operation that may result 

in potential damage to the product, injury to the user, or render 

the product unsafe.

annotations

WARNING

:

 This product can expose you to chemicals including 

lead, which is known to the State of California to cause cancer and/

or birth defects or other reproductive harm. For more information, go 

to www.P65Warning.ca.gov.

Summary of Contents for GEN2 i4.0





























Reviews: