background image

G-6

05-E3B, 05-E3BG, WSM

G  GENERAL

CAUTION

• When changing or inspecting, be sure to level and stop the engine.

NOTE

Engine Oil :

• Refer to the following table for the suitable American Petroleum Institute (API) classification of engine oil

according to the engine type (with internal EGR, external EGR or non-EGR) and the Fuel Type Used : 
(Low Sulfur, Ultra Low Sulfur or High Sulfur Fuels).

EGR : Exhaust Gas Re-circulation

W1024941

• CJ-4 classification oil is intended for use in engines equipped with DPF (Diesel Particulate Filter) and is

Not Recommended for use in Kubota E3 specification engines.

• Oil used in the engine should have API classification and Proper SAE Engine Oil Viscosity according to

the ambient temperatures where the engine is operated.

• With strict emission control regulations now in effect, the CF-4 and CG-4 engine oils have been developed

for use with low sulfur fuels, for On-Highway vehicle engines.  When a Non-Road engine runs on high
sulfur fuel, it is advisable to use a "CF or better" classification engine oil with a high Total Base Number
(a minimum TBN of 10 is recommended).

Fuel :

• Cetane Rating : The minimum recommended Fuel Cetane Rating is 45.  A cetane rating greater than 50 is

preferred, especially for ambient temperatures below 

20 °C (

4 °F) or elevations above 1500 m (5000 ft).

• Diesel Fuel Specification Type and Sulfur Content % (ppm) used, must be compliant with all applicable

emission regulations for the area in which the engine is operated.

• Use of diesel fuel with sulfur content less than 0.10 % (1000 ppm) is strongly recommended.
• If high-sulfur fuel (sulfur content 0.50 % (5000 ppm) to 1.0 % (10000 ppm)) is used as a diesel fuel, change

the engine oil and oil filter at shorter intervals.  (approximately half)

• DO NOT USE Fuels that have sulfur content greater than 1.0 % (10000 ppm).
• Diesel fuels specified to EN 590 or ASTM  D975 are recommended.
• No.2-D is a distillate fuel of lower volatility for engines in industrial and heavy mobile service.  (SAE J313

JUN87)

• Since KUBOTA diesel engines of less than 56 kW (75 hp) utilize EPA Tier 4 and Interim Tier 4 standards,

the use of low sulfur fuel or ultra low sulfur fuel is mandatory for these engines, when operated in US EPA
regulated areas.  Therefore, please use No.2-D S500 or S15 diesel fuel as an alternative to No.2-D, and use
No.1-D S500 or S15 diesel fuel as an alternative to No.1-D for ambient temperatures below 

10 °C (14 °F).

1) SAE : Society of Automotive Engineers 
2) EN : European Norm
3) ASTM : American Society of Testing and Materials 
4) US EPA : United States Environmental Protection Agency 
5) No.1-D or No.2-D, S500 : Low Sulfur Diesel (LSD) less than 500 ppm or 0.05 wt.% 

         No.1-D or No.2-D, S15 : Ultra Low Sulfur Diesel (ULSD) 15 ppm or 0.0015 wt.%

           Fuel Type

Engine oil classification (API classification)

Engines with non-EGR 
Engines with internal EGR

Engines with external EGR

High Sulfur Fuel 
[0.05 % (500 ppm) 

≤ 

Sulfur Content 

0.50 % (5000 ppm)]

CF
(If the "CF-4, CG-4, CH-4, or CI-4" engine 
oil is used with a high-sulfur fuel, change 
the engine oil at shorter intervals.  
(approximately half))

Low Sulfur Fuel 
[Sulfur Content 

<

 

0.05 % (500 ppm)] or 
Ultra Low Sulfur Fuel 
[Sulfur Content 

<

 

0.0015 % (15 ppm)]

CF, CF-4, CG-4, CH-4 or CI-4

CF or CI-4
(Class CF-4, CG-4 and CH-4 engine oils 
cannot be used on EGR type engines.)

KiSC issued 12, 2007 A

Summary of Contents for N3.30


































































































































Reviews: