manualshive.com logo in svg

NAKTO Elegance, Manual

Share
Download
NAKTO Elegance Manual Download Page 2

Let’s start assembling your NAKTO  Elegance  ebike!

(Please read this entire assembly manual before assembly as it will save 

you a lot of time!)

Step One: Unpack the ebike.

1.Pull the frame and all parts (charger, seat, tookit, keys & fuse, manual, 

nut caps, rear cushion and pedals) out of cardboard box. Separate bike 

from foam padding. Cut off all zip ties with scissors while being extra 

careful as not to damage the paint or cut any wires or cables.

Notice:

 

Keep the spare fuse in a safe place.It is not used for assembly and will be 

used for the replacement if the original fuse were damaged.

Ensure all the following pieces are included with the Nakto Elegance.

Assembly Instructions: Elegance

Tools included: 

S

crewdriver, Phillips & Slotted 2 in 1

 

               Double open-end wrench, 13mm/15mm

                                  Allen wrench, 5mm

                                  Allen wrench, 6mm

Tools needed: 

Scissor        

                                Bike pump

Summary of Contents for Elegance
































Reviews:

No comments

Brands by name

Popular brands

Load more brands