7
System Operation
W-1Ku receiver
Powering the Vr-3u receiver
Slide the receiver’s
BaTTerY DOOr (6)
by
pressing the
Open
tab, then pop hinged
door open. Insert two fresh AA alkaline
batteries in the
BaTTerY COMParTMenT (7)
,
observing the correct polarity. Close the
battery door and secure by pressing
Close
and sliding closed.
Turn the receiver on by rotating the
VOluMe/
On-OFF KnOB (1)
clockwise till it clicks. The
unit is now in standby and the
rF/lOW
BaTTerY leD (3)
remains dark. If the RF/Low
Battery LED turns red during use, replace
batteries. To preserve battery life, turn the
receiver off when it is not in use.
Note:
Although a fresh alkaline battery can last up
to 8-10 hours in use in the receiver, in order to
ensure optimal performance it is recommended
that the receiver batteries be replaced after five
hours use.
antenna
When the system is in use, the VR-3U
receiver’s standard wire
anTenna (4)
should
be fully extended, avoiding obstructions,
to obtain maximum range.
rF Mute (Squelch) adjustment
In normal operation there is no need to set
or adjust the mute level. The receiver has an
internal factory preset mute level for optimal
performance.
Connecting audio Output
Plug one end of the audio cable (3.5mm
jack) provided into the
OuTPuT jack (2)
. The
other end (XLR jack) should be plugged into
your camcorder or mixer audio input jack.
Monitoring through the Camcorder
Many camcorders allow the user to monitor
by providing a headphone jack. If you plug
your headphones into the camcorder, you
may need to make a simple adjustment on
the VR-3U receiver. If the sound you hear is
uncomfortably loud or sounds distorted, turn
the Volume/On-Off knob on the receiver
counter-clockwise until good audio quality
is obtained. If volume is too low, turn the
Volume/On-Off knob clockwise until you
obtain a comfortable volume level.
uH-3 Handheld Mic Transmitter
Unscrew the
BaTTerY COVer (16)
and
remove, exposing the
BaTTerY HOlDer (17)
.
Insert two fresh
aa alKalIne BaTTerIeS
(18)
, observing the correct polarity as
marked, and screw the cover back on to
the microphone. Make sure the cover is
screwed on completely.
Note:
Although fresh alkaline batteries can last
up to 10 hours in use, in order to ensure optimal
performance it is recommended that you replace
the batteries after every 7-8 hours of use. To
preserve battery life, turn the transmitter off when
not in use.
Before turning on the UH-3, slide the
auDIO
MuTe SWITCH (19)
to the OFF position.
Then slide the
POWer SWITCH (21)
to the
On position.
The POWer InDICaTOr leD (22)
will light steady, indicating usable battery
strength. In the case of a dead or low
battery, the
BaTTerY InDICaTOr leD (20)
will either not go on at all or will stay on
continuously, indicating that the batteries
should be replaced with fresh ones.
To preserve battery life, turn the transmitter
off when not in use.
The microphone is now ready to use.
The receiver
rF/lOW BaTTerY leD (3)
should
now be lit, indicating a received signal from
the transmitter. When ready to speak, slide
the
auDIO MuTe SWITCH (19)
to the On
position. Adjust the
VOluMe/On-OFF KnOB (1)
on the receiver as per
Monitoring through
the Camcorder
.
Note:
Observe care in selecting P.A. volume,
transmitter location and speaker placement so
that acoustic feedback (howling or screeching)
will be avoided.
