background image

7

1. Unscrew the 

BATTERY COMPARTMENT COVER (16) 

and remove, exposing the

BATTERY HOLDER (17

). Insert a fresh 

9V ALKALINE BATTERY (18

), observing the

correct polarity as marked, and screw the cover back on to the microphone. Make
sure the cover is screwed on completely. Fresh alkaline batteries can last up to 10
hours in use, but in order to ensure optimum performance, it is recommended that
you replace the battery after every 6-8 hours of use.

2. Turn on the UH by sliding the  

OFF/STANDBY/ON SWITCH (19) 

to the STANDBY

position first (transmitter on, audio muted) or the ON position (transmitter and audio
both on). The 

BATTERY INDICATOR LED (20)

 will give a single quick flash, indicating

usable battery strength. In the case of a dead or low battery, the LED will either not
go on at all or will stay on continuously, indicating that the battery should be
replaced with a fresh one. To preserve battery life, turn the transmitter off when not in
use.

3. The microphone is now ready to use. The 

A or B

 

DIVERSITY LED INDICATORS (13)

on the UHF-7 receiver should now be lit, indicating a received signal from the
transmitter. When ready to speak, slide the 

OFF/STANDBY/ON SWITCH (19)

 to the

ON position. Adjust the volume of the receiver as per the Audio Output Microphone
Connection section of the above UHF-7 receiver instructions.

[Note: Observe care in selecting P.A. volume, transmitter location and speaker
placement so that acoustic feedback (howling or screeching) will be avoided.]

4. For optimum performance, an 

INPUT LEVEL CONTROL (21) 

is provided. Adjust the

gain by turning the control with a small screw driver. Set for maximum possible gain
without audible distortion on the high level peaks. (Note: Turning down the gain too
much can compromise the signal-to-noise and is not recommended.)

UH HANDHELD MICROPHONE TRANSMITTER

16

17

18

19

6

12

11

15

13

14

15

10

9

8

6

5

7

2

1

2

4

3

1

4

20

21

Summary of Contents for UHF-7







Reviews: