To ensure years of enjoyment from your NADY AUDIO PSS-
150 Portable Sound System, please read and understand this
manual thoroughly before using the unit.
1. INSPeCTION
Your NADY AUDIO PSS-150 Portable Sound System was
carefully packed at the factory in packaging designed to protect
the units in shipment. Before installing and using your unit,
carefully examine the packaging and all contents for any signs of
physical damage that may have occurred in transit.
[Please note: Nady Systems is not responsible for shipping
damage. If your unit is damaged, do not return to NADY, but
notify your dealer and the shipping company (if shipped to you)
immediately to make a claim. Such claims must be made by the
consignee in a timely manner.]
CONTeNTS:
PSS-150 Mixer Section
PSS-150 Left Speaker
PSS-150 �ight Speaker
(2x) Speaker Stands
(2x) 2 30’ Speaker Cables
SP-1 Starpower™ Microphone
XC-20 20’ Microphone Cable
AC cord
Instruction Manual
Warranty Card
2. SeTUP
After transporting the PSS-150 to the desired location, lay the unit
down on its flat side. Unclasp the side panel latches by pulling
up on the yellow tab to release and unhook the latch. Carefully
lift off the speakers and then remove the speaker stands and
accessories from inside the unit.
Mixer Section
Position the PSS-150 mixer section on its flat surface with the
control panel facing up. Parts of the unit can become very warm
during use. This is normal during operation. Care should be taken
to ensure that there is enough space behind the Mixer Section for
cooling. Also, do not place the Portable Sound System on high
temperature devices such as power amplifiers, etc., or the unit
may overheat in operation.
Although the PSS-150 is shielded against radio frequency (�F)
and electromagnetic interference (EMI), extremely high fields of
�F and EMI should be avoided.
Please make sure that the power unit supplied is marked for the
correct voltage in your area (120VAC/60 Hz or 230VAC/50 Hz).
Power requirements for electrical equipment differ from area to
area. In new installations and portable sound systems, or any
situation in which the AC power is in question, it is wise to confirm
the voltage and use the appropriate power supply unit before
connecting it to power sources.
•
•
•
•
•
•
•
•
•
•
europe (except UK): 230V, 50Hz
UK and Australia: 240V, 50Hz
USA and Canada: 120V, 60 Hz
For other areas, please check with local authorities.
Speakers and Stands
Fully extend the speaker stand tripod legs and tighten the base
thumbscrew. Extend the pole of the stand to the desired height
and insert the safety pin completely through the stand hole above
the pole thumbscrew. Lower the pole so that the pin rests on the
holder and tighten the pole thumbscrew.
Setup the stands on a flat surface where the speakers will be
located and not disturbed. Place the speakers on the stands and
position them as desired. Note: facing the speakers towards any
of the microphones connected with the PSS-150 will increase the
chance of feedback.
Connect the speaker cables to the input jacks on the lower left
front panel of both the Left and �ight speakers. Connect the other
end of each cable to the corresponding Left and �ight speaker
outputs on the rear panel of the PSS-150 mixer section. Position
the length of the cables so they will not be a safety hazard to
people.
WARNING:
Connect only the supplied speakers to the PSS-150.
Never connect additional speakers to the PSS-150.
Inputs
Connect all sound sources to the appropriate inputs i.e.,
microphones, keyboards, CD players, karaoke machines.
The supplied SP-1 Starpower™ microphone is an all-purpose
professional stage and recording microphone with rugged metal
construction and excellent clear, transparent sound across the
spectrum.
When ready to operate, plug the AC cord into the power source.
Make sure that the unit is turned off before connecting to the AC
power source to avoid possible loud transients which can damage
your speakers or your ears. Before turning on, connect up the
speakers and all inputs and outputs desired and turn down the
Master Volume.
4
Installation
