background image

1. Rackmounting the Receiver

There are two options available for rackmounting the Encore II receiver: 

singly or side‑by‑side with another Encore Series receiver. 

a. 

Single mounting:

 Remove the receiver 

SIDE MOUNT CLIP (1)

 from each side of 

the receiver (as shown) and slide in the optional 

ERM-12 RACK EARS (9)

b. 

Side-by-side double mounting:

 After removing the 

SIDE MOUNT CLIPS (1)

 from 

both Encore receivers, join the two receivers with the 

EJC-2 JOINING CLIP (10) 

and attach the 

ERM-22 RACK EARS (12)

 as shown.

 

(Note: Do not mount the receiver in a rack directly above an amplifier or 

other source of high heat — this could degrade the performance of the 

Encore I. Always ensure adequate airflow and heat dissipation in any rack 

configuration.) 

2. Powering the Receiver

Plug the 

12V AC/DC ADAPTER (15)

 provided into the 

DC INPUT JACK (11)

 on 

the back of the receiver. Then plug the power supply into an AC outlet. 

(Note: Any 12V DC source with 400mA capability can also be used.) 

Press the 

POWER SWITCH (8)

 once to turn on the receiver. The 

POWER ON LED (7)

 

will now light and the receiver is operational.

3. Antennas

The Encore II receiver is supplied with 

TELESCOPIC ANTENNAS (16). 

These should  be 

extended fully to obtain maximum range.  Optimal antenna position is 45 degrees 

from the receiver (at 90 degrees from each other). For maximum range, it is always 

best to maintain a line of sight (no obstructions) between the receiver antennas and 

the transmitter at all times whenever possible.

4. Mute (Squelch) Adjustment

In normal operation, the 

MUTE CONTROL (2)

 should be set fully counterclockwise to 

the factory preset minimum RF level.  However, in areas of high RF activity, the mute 

(or squelch, as it is sometimes called) may need to be adjusted to compensate for the 

adverse conditions in a particular location.  If, with the transmitter off, the receiver’s 

A and/or B 

DIVERSITY LED INDICATORS (3) 

and/or one or more LEDs of the 

5 LED RF 

LEVEL DISPLAY (4) 

 flicker or stay on, the squelch control should be turned clockwise 

until the LEDs extinguish.  When the squelch is properly adjusted, the A and/or B 

LEDs or the 

RF LEVEL LED

 displays will only light when the system transmitter is turned 

on.  Turning the squelch control too far clockwise will reduce the range, but yield a 

quieter mute (squelch) function. During operation, especially at ranges greater than 

75 feet, one or the other of the A or B LEDs may extinguish briefly. This is normal—

the unit’s DigiTRU Diversity

 reception ensures that the received audio will not be 

interrupted. When both the A/B DIVERSITY LEDs and the 5 LED RF LEVEL display 

extinguish, the transmitter is out of range for that given location, and the user should 

move closer to the receiver to re‑establish the radio link.

4

ENCORE II RECEIVER

Summary of Contents for ENCORE 2

















Reviews: