background image

SPECIFICATIONS

10

POWER SPECIFICATIONS

XA-900

XA-1100

2

400 + 400

730 + 730

4

300 + 300

475 + 475

8

200 + 200

300 + 300

Bridged 4

675

1100

ELECTRICAL SPECIFICATIONS

XA-900

XA-1100

INPUT SENSITIVITY

1.15V (+3.4dBU)

1.15V (+4dBU)

INPUT IMPENDANCE

10K

 Unbalanced & Balanced

FREQUENCY RESPONSE

20Hz~20KHz +/-1dB

(at 10dB below rated output power)

-3dB points:5Hz~50KHz

VOLTAGE GAIN

32dB

34dB

DISTORTION (SMPTE-1M)

<0.03%

<0.03%

S/N RATIO

100dB

100dB

GENERAL SPECIFICATIONS

XA-900

XA-1100

Full short circuit, open circuit, thermal,

PROTECTIONS

ultrasonic, and RF protection; stable into

reactive or mismatched loads; ON/OFF

muting; current limiter (crowbar)

Front: Power switch, 40 dentent input level

control for each channel. Rear Parallel/

CONTROLS

Mono/Bridge selector, ground lift switch,

AC voltage selector switch

SIGNAL 2x green LED

INDICATORS

CLIP: 2 x red LED

POWER: 2 x green LED

PROTECT: 2 x red LED

CONNECTORS

POWER: IEC power cord jack

INPUT: Active balanced XLR and

1/4” 6.3mm) TRS

OUTPUT: “Touch-proof” binding posts

POWER SUPPLY

Voltage selectable: 110-120V or 220~240V

AC 50/60Hz

FUSES

3AG, 20A/250V (X2)

DIMENSIONS

19.0” x 15.7” x 3.5” (483 x 400 x 88.8mm)

WEIGHT

38.5lb (17.5Kg)               41.8lb (18.8Kg)

The specifications above are correct at the time of printing of this manual. For improvement purposes, all specifications
for this unit, including design and apperance, are subject to change without prior notice.

EIA OUT POWER

1HZ, THD MAXIMUM 1%

BOTH CHANNELS

Summary of Contents for XA













Reviews: