background image

1  STANDBY BUTTON

• 

Press this button to switch ON the C 390DD from standby mode. 
The Standby LED indicator will turn from amber to blue and 
illuminate the VFD. Pressing the STANDBY button again turns the 
unit back to standby mode. 

NOTE

 

In order to turn ON the C 390DD from standby mode or back to standby 
mode, the rear panel POWER switch must be in the ON position.

2  STANDBY LED

• 

This indicator will light up amber when the C 390DD is at standby 
mode.

• 

When the C 390DD is powered up from standby mode, this 
indicator will illuminate blue.

 

3  NAVIGATION and ENTER BUTTONS

The navigation [

d/f/a/s

] and [ENTER] buttons have various 

applications specific to given modes. The middle round button is 
designated as [ENTER] button; this is normally pressed to complete a 
selection, procedure, sequence or other applicable functions.

4  DIGITAL USB FRONT

• 

Connect a USB mass storage device to this input. Typical USB mass 
storage devices compatible with C 390DD include portable flash 
memory devices and external hard drives (FAT32 formatted). 

• 

Refer also to the item about LISTENING TO USB DEVICE at the OTHER 
FEATURES section of the OPERATION page.

5  VACUUM FLUORESCENT DISPLAY (VFD)

• 

Display visual information about the current Source. Information 
supplied is generated by the Source.

• 

Show menu options and other related functions.

6   REMOTE SENSOR

• 

Point the AVR 4 remote control at the remote sensor and press the 
buttons.

• 

Do not expose the remote sensor of the C 390DD to a strong light 
source such as direct sunlight or illumination. If you do so, you may 
not be able to operate the C 390DD with the remote control. 

Distance:

 About 23ft (7m) from the front of the remote sensor.

Angle:

 About 30

o

 in each direction of the front of the remote sensor.

a

 SOURCE 

s

• 

Toggle through the input selections - Digital Coaxial 1, Digital 
Coaxial 2, Digital Optical 1, Digital Optical 2, Digital AES/EBU, 
Computer, Digital USB Back and Digital USB Front. 

• 

If the optional modules like the DD HDMI 1 (Direct Digital 
HDMI) and the DD AP 1 (Direct Digital Analog/Phono) modules 
are installed, the source selections will continue on with the 
corresponding sources of said modules.

8 VOLUME 

• 

The VOLUME control adjusts the overall loudness of the signal being 
fed to the loudspeakers. Volume control is characterized by perfect 
signal tracking and channel balance. It gives a highly linear and low 
noise operation.

• 

Turn clockwise to increase the volume level; counter clockwise to 
lower it.

IDENTIFICATION OF CONTROLS

FRONT PANEL

4

5

6

7

8

1

2

3

6

ENGLISH

FR

ANÇ

AIS

ESP
AÑOL

IT

ALIANO

DEUT

SCH

NEDERL

ANDS

SVENSK

A

РУ

ССКИЙ

Summary of Contents for C 390DD

























Reviews: