NAD C 328 User Manual Download Page 3

23. Battery Disposal 

- When disposing of used batteries, please comply 

with governmental regulations or environmental public instruction’s 
rules that apply in your country or area.

24. Safety Check 

- Upon completion of any service or repairs to this 

product, ask the service technician to perform safety checks to 
determine that the product is in proper operating condition. 

25. Wall or Ceiling Mounting 

- The product should be mounted to a wall 

or ceiling only as recommended by the manufacturer.

WARNING

The lightning flash with arrowhead symbol, within an 
equilateral triangle, is intended to alert the user to the 
presence of uninsulated “dangerous voltage” within the 
product’s enclosure that may be of sufficient magnitude to 
constitute a risk of electric shock to persons

The exclamation point within an equilateral triangle is intended 
to alert the user to the presence of important operating 
and maintenance (servicing) instructions in the literature 
accompanying the appliance.

THE EQUIPMENT MUST BE CONNECTED TO AN EARTHED MAINS SOCKET-OUTLET.

CAUTION REGARDING PLACEMENT 

To maintain proper ventilation, be sure to leave a space around the unit 
(from the largest outer dimensions including projections) than is equal to, 
or greater than shown below. 

 

Left and Right Panels: 10 cm 

 

Rear Panel: 10 cm 

 

Top Panel: 10 cm 

FCC STATEMENT

This equipment has been tested and found to comply with the limits for Class 
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following 
measures:

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.

• 

Consult the dealer or an experienced radio TV technician for help.

CAUTION
• 

Changes or modifications to this equipment not expressly approved 
by NAD Electronics for compliance could void the user’s authority to 
operate this equipment. 

• 

To prevent electric shock, match wide blade of plug to wide slot, fully 
insert. 

• 

Danger of explosion if battery is incorrectly replaced. Replace only with 
the same or equivalent type.

• 

An appliance with a protective earth terminal should be connected to a 
mains outlet with a protective earth connection.

WARNING
• 

To reduce the risk of fire or electric shock, do not expose this apparatus 
to rain or moisture.

• 

The apparatus shall not be exposed to dripping or splashing and 
that no objects filled with liquids, such as vases, shall be placed on 
apparatus.

• 

Mains plug is used as disconnect device and it should remain readily 
operable during intended use. In order to disconnect the apparatus 
from the mains completely, the mains plug should be disconnected 
from the mains socket outlet completely.

• 

Battery shall not be exposed to excessive heat such as sunshine, fire or 
the like.

IF IN DOUBT CONSULT A COMPETENT ELECTRICIAN.

This product is manufactured to comply with the radio 
interference requirements of EEC DIRECTIVE 2004/108/EC.

NOTES ON ENVIRONMENTAL PROTECTION

At the end of its useful life, this product must not be disposed 
of with regular household waste but must be returned to a 
collection point for the recycling of electrical and electronic 
equipment. The symbol on the product, user’s manual and 
packaging point this out. 

The materials can be reused in accordance with their markings. Through 
re-use, recycling of raw materials, or other forms of recycling of old 
products, you are making an important contribution to the protection of 
our environment. 

Your local administrative office can advise you of the responsible waste 
disposal point. 

RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT) 

The model and serial number of your new C 328 are located on the back of 
the cabinet. For your future convenience, we suggest that you record these 
numbers here: 

 

Model number : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 

Serial number :  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IMPORTANT SAFETY INSTRUCTIONS

 

 

 

 

 

 

 

NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited

Copyright 2017, NAD Electronics International, a division of Lenbrook Industries Limited

3

ENGLISH

FR

ANÇ

AIS

ESP

AÑOL

IT

ALIANO

DEUT

SCH

NEDERL

ANDS

SVENSK

A

РУ

ССКИЙ

Summary of Contents for C 328












Reviews: