NAD C 245BEE Owner'S Manual Download Page 10

condition

poSSible cauSeS

poSSible SolutionS

No power.

The power cord is disconnected.

Plug the power cord into the wall outlet 

securely.

C 245BEE at standby mode.

Press front panel STANDBY button to switch 

ON the C 245BEE.

Rear panel POWER switch not at ON setting.

Set the rear panel POWER switch to ON 

setting.

C BEE always at standby mode; 

cannot be switched ON using the 

front panel STANDBY button.

+12V TRIGGER IN/INPUT SENSE switch set to “AUTO” 

position and a jack is plugged-in at +12V Trigger IN 

socket or an input signal is applied at the rear panel 

CHANNEL A IN or CHANNEL B IN sockets.

Slide the +12V TRIGGER IN/INPUT SENSE 

switch to “OFF” position and unplug the jack 

at the +12V Trigger IN socket or remove 

the input signal applied at the rear panel 

CHANNEL A IN or CHANNEL B IN sockets.

The C 245BEE is not powered OFF using the front 

panel STANDBY button.

Power ON the C 245BEE in the same manner 

by which it was deactivated.  

No sound.

Power AC lead unplugged or power not switched ON.  

Check if AC lead is plugged-in and POWER 

switched ON (along with the corresponding 

ATO logic configuration).

Front panel CHANNEL A or CHANNEL B button is not 

activated.

Press CHANNEL A or CHANNEL B to select 

active input signal available at the rear panel 

CHANNEL A IN or CHANNEL B IN sockets.

No input signal applied through the rear panel 

CHANNEL A IN or CHANNEL B IN sockets.

Ensure that there is active input signal 

applied through the rear panel CHANNEL A 

IN or CHANNEL B IN sockets.

No sound one channel.

Speaker not properly connected or damaged.

Check connections and speakers.

Input lead disconnected or damaged.

Check leads and connections.

Weak bass/diffused stereo image.

Speakers wired out of phase.

Check connections to all speakers in the 

system.

STANDBY LED stays red upon 

setting POWER switch to ON.

There is short circuit in the speaker cabling.

Switch C 245BEE OFF and check speaker 

cable connections for both speaker terminals 

at the rear panel. 

REFERENCE

troubleShooting

10

EN

G

LIS

H

FR

A

N

Ç

A

IS

ES

PA

Ñ

O

L

IT

A

LIA

N

O

D

EU

TS

CH

N

ED

ER

LA

N

D

S

SV

EN

SK

A

РУ

СС

К

И

Й

Summary of Contents for C 245BEE













Reviews: