N1C N1C.L1000 User Manual Download Page 21 | Manualshive

Page: 21 / 55

background image

N1C L-Series(1-3kVA) UPS

User Manual

2 Overview

13

2.2.3 EPO Connector

When connecting two ports in the EPO connector together, UPS will close output. If it needs to recover

output, disconnect two ports in the EPO connector and power UPS off, and then restart UPS.

2.2.4 Intelligent Slot

SNMP card

SNMP card can achieve the remote monitor for the input voltage and frequency, output voltage and

frequency, load, etc. of the UPS and remote ON/OFF operation, as shown in Figure2-10.

Figure2-10

SNMP card

RS485 and dry contact(optional)

The pin sequence and pin definition of RS485 and dry contact is as shown in Figure2-11 and Figure2-

12.

Figure2-11

RS485 and dry contact

«
...
19
20
21
22
23
...
»

Summary of Contents for N1C.L1000
























































Reviews:

No comments

Related manuals for N1C.L1000

Brand: Tripp Lite Pages: 5

Brand: East Pages: 16

XP Pro evolution

Brand: INFOSEC UPS SYSTEM Pages: 72

Brand: AEG Pages: 32

Brand: AEG Pages: 56

PROTECT 1 Series

Brand: AEG Pages: 64

Compumaster 1000

Brand: AEG Pages: 29

Protect 2.33 2.0

Brand: AEG Pages: 80

Brand: AEG Pages: 63

Brand: AEG Pages: 81

Brand: AEG Pages: 56

Fluxpower HE 10 kVA

Brand: AEG Pages: 56

A PROTECT B. 1500

Brand: AEG Pages: 54

Brand: AEG Pages: 100

Brand: AEG Pages: 6

Brand: AEC Pages: 20

Brand: AirSpace Pages: 23

Brand: Astrid Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands