background image

(Revised 2011-09-02) 

14 

FCC STATEMENT 

 
This product complies with Part 15 of the FCC-A Rules. 
Operation is subject to the following conditions: 
(1)

 

This device may not cause harmful interference 

(2)

 

This  device  must  accept  any  interference  received,  including  interference  that  may  cause  undesired 
operation. 

 
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. Operation of this device in a residential area is likely to cause 
harmful interference in which case the user will be required to correct the interference at his own expense. 
 

 
 
INDUSTRY CANADA 
 

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment 
Regulations. Operation is subject to the following two conditions; (1) this device digital apparatus meets all 
requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the 
following two conditions; (1) this device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that may cause undesired operation. 

 

Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant 
des règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne 
pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y 
compris l'interférence qui peut causer l'opération peu désirée. 

 

Summary of Contents for 100-POE4


















Reviews: