N-BIOTEK MINI-CELL NB-203M Operation Manual Download Page 17

Page  17  /  17 
 

 

8. Humidity   

Mini CO

  incubator adopts natural humidity system by water container as below image. 

Please fill up distilled water up to the water line of water tray and keep lid closed for proper humidity level 

(at about 80%) during operation of incubator.   

Place the water container be close to back of chamber so the container is more exposed to heated air 

directly from water pass.   

No water is recommendable when carrying this incubator.   

In case that humidity is necessary during carriage, ensure the water container 

to be securely held at bottom of chamber(like using sticky mat or tape) and    wet 

sponge  or  sterilized  gauze  is  recommendable  rather  than  filling  water.  In  this 

situation,  humidity  may  not  be  reaching  to  maximum  or  normal  humidity  like 

normally max humidity up to 80%.       

 

9. Alarm 

 

Turn alarm system ON by pressing alarm button for about 5 seconds. When switching alarm on or off, 

a short alarm will come out. When alarm system is on, LED lamp is OFF. When alarm system is off, 

LED lamp of alarm is lighting to indicate that alarm system is disarmed.     

In order to activate alarm system, it should maintain 

±2

°

C,

 

± 

1%(CO2) from set point for 3 minutes. 

This course is recognised as stabilizing process. 

After stabilizing process, alarm system will be armed and alarm event is as below. 

 

Alarm Activation 

 

Temperature : (bird singing) 

- If it stays out of 

±1℃ 

from

 

set

 

point  for 8~9 minutes, it will give you an alarm. 

- Alarm will automatically stop once temperature is recovered into tolerance range. 

- Pressing mute button once will give 10 minutes delay.   

 

 

CO2 : (bird singing) 

- If it stays out of 

± 

1%

 

from

 

set

 

point  for 8~9 minutes, it will give you an alarm.   

- Alarm will automatically stop once CO2 is recovered into tolerance range. 

- Pressing mute button once will give 10 minutes delay.   

 

Door Open : 

  - Alarm comes out 30 seconds after door opening. 

  And no alarm come out if door is closed within 30 seconds. 

  - If door is closed during alarm, alarm will stop immediately.   

  - Pressing mute button in the situation of door open will give 3 minutes alarm delay. 

Summary of Contents for MINI-CELL NB-203M


















Reviews: