MyTek Stereo96 Series User Manual Download Page 2

Page: 2 / 11

This manual may be updated

Download the newest version at:

For technical support, technical tips and support check:

or contact Mytek tech support at:

or at:

tel. (646)-613 1822
fax.(212)-202 5331

Mytek

151 Lafayette Street 3rd Fl

New York NY 10013

USA

http://www.mytekdigital.com/manuals/stereo96adc_manual.pdf

http://www.mytekdigital.com/products/stereo96adc.htm

[email protected]

Quick Start……………………………………………….3

Operation- Internal jumper settings........................……...5

Operation- Typical setup -Balanced Signal Source……...7

Operation- Analog input alignment……………...………9

Operation- Unbalanced Signal Source…….......................10

Rack mount shelf.......................................….....................17

Companion Stereo96 DAC…………………………….....18

Introduction..…………………………………….............4

Sampling frequencies and External synchronization…....12

SuperShaper-HR ™ Noise shaping and dithering…..........14

Specifications…………………………………………......19

Warranty conditions……………………………………...20

Summary of Contents for Stereo96 Series












Search results

Summary of Contents for Stereo96 Series

Reviews:

Related manuals for Stereo96 Series

Brands by name

Popular brands

MyTek Stereo96 Series, User Manual

Search results

Summary of Contents for Stereo96 Series

Reviews:

Related manuals for Stereo96 Series

Brands by name

Popular brands