3
PRODUCT FEATURES:
Grate
Tub
Heating Light
Indicates wax is
melting
Ready Light
Indicates wax is ready
for use
3 Bags of Paraffin Wax
Lid
With locking
mechanisim
INSTRUCTIONS FOR USE
This unit is controlled by a thermostat. The unit can hold a maximum of 3 bags
(1.4 kg approx.) of paraffin wax for operation. The melting time is less than 2
hours and it is designed to run continuously for 24 hours a day.
I
mportant note:
This unit may feel very warm to sensitive skin. However, in
order to fully experience the benefits of warm paraffin, the wax must be melted
to a temperature between 50-55 degrees Centigrade. For proper application,
quickly dip the body area (i.e. hand or elbow) into the melted paraffin wax and
remove immediately. Wait a few seconds for wax to solidify. This should be
repeated 6–10 times. Never soak in the wax for more than 1–2 seconds. If you are
very sensitive to heat or feel that this appliance may not be for you, please return
this product to the place of purchase, prior to use.
How to set up the Paraffin bath
1. Remove all contents from packaging and check to make sure you have all of the
following components of the Paraffin Wax Treatment bath:
1.
• Paraffin bath tub with locking lid
1.
• Plastic grate
1.
• 3 bags of Paraffin Wax
1.
• 20 plastic bags
2. Place unit on a level and sturdy table
or surface and open the lid.
3. Make sure paraffin bath tub is empty
before putting wax into tub.
4. Open the bags of Paraffin Wax and
place wax in the tub. Open only as
many bags as you plan to use. The unit
is designed to hold a maximum of 3
bags (1.4 kg approx.) of melted
paraffin wax and a minimum of 2.5
bags (1.1 kg approx.). Always keep the
level of melted paraffin wax filled to
between the MIN and MAX levels
marked on the inside of the tub (Fig.1).
5. Plug the unit into a 220-240V A/C
household outlet.
6. Close the locking lid. Push power
button. “Heating” illuminates red while
wax is melting (Fig. 2). Most of the
paraffin wax should melt within 2
hours.
7. “Ready” light will come on when the
majority of the wax has melted. If
necessary, replace the lid and allow a
futher 15 min for any remaining wax to
melt.
8. Open the lid and carefully place the grate into the wax and allow it to sink to the
bottom of the tub (Fig. 3). The Paraffin Wax Treatment unit is designed to be
used at room temperature. If the wax starts to solidify or flakes form on the top
surface, close lid and press power button twice and wait for the “ready” light.
Note:
The temperature of the room can have an effect on the unit’s performance.
Therefore we always recommend testing the paraffin temperature on the inside
of the wrist area before dipping your entire hand or elbow.
Note:
NEVER open lid or dip your hand, foot or elbow while the “heating” light is
flashing.
Note:
Place the grate into the unit only when the paraffin wax is melted.
How to use the Paraffin bath
1. Before immersing your hand or elbow test the paraffin wax on the inside of
your wrist to make sure the temperature of the wax is comfortable. Remove all
jewellery before dipping (i.e. rings, bracelets, watch).
Note:
It is suggested you wash the area to be treated and apply lanolin-based
hand lotion over the area before dipping it into the paraffin wax. This will allow
the wax to be removed easier and will help moisturize the skin.
2. Dip your hand, elbow or foot into the melted paraffin wax and remove
immediately. Wait a few seconds until the wax solidifies. Try to avoid moving
your hand or elbow while wax is applied.
Note:
Dipping process is quick. Do not leave hand or elbow in the tub. Do not
soak. Dip quickly in and out.
3. Repeat this step several times until several layers have formed; 6–10 coatings
are suggested.
MAX
MIN
Fig. 1
Fig. 2
Fig. 3
20 Plastic Bags
IB-PAR350MYAGB-0415-01_Layout 1 02/06/2015 09:51 Page 3
