Display setup
The Display Setup specifies the parameters for
the On Screen Display. In each case the the
LEFT and RIGHT keys may be used to alter
the parameter selected.
•
Select TV System to switch between NTSC
and PAL to suit your TV monitor.
•
Superimpose allows the OSD either
to replace the TV picture (Off), or be
superimposed over it (On).
•
During normal operation of the MDP 500,
it is possible to have a “temporary” OSD
appear for a few seconds every time any
adjustment is made. This is set using the
“Temp. Display” parameter which may
be set to Full, Simple, or Off as desired.
•
Video Format can be set to S-Video or
Composite, or Auto – that automatically
selects the best source present.
•
The OSD Output can be sent to the
Composite, or S-Video Monitor outputs,
or both, or it may be switched Off.
•
OSD style changes the screen text colour
if Superimpose is switched Off.
•
EXIT returns to the main menu
Trigger setup
The Trigger Setup specifies the parameters
for the DC Trigger outputs (see page 4).
Each of the trigger parameters may be set
separately for “Trig1” which controls the
TRIGGER 1 output and “Trig2” which
controls the TRIGGER 2 and TRIGGER 3
outputs. Use the UP and DOWN keys to
select which parameter you wish to change.
In each case the the LEFT and RIGHT keys
are used to alter the parameter selected.
•
“sense” sets what controls activate the
Trigger output. Set to Power On to activate
the trigger when switching out ofSTANDBY
(and de-activate it when returning to
STANDBY). Alternatively the trigger output
may be activated when any of the inputs is
selected (Tuner, CD, DVD, TV, VCR, SAT,
Aux1, Aux2 and 7.1CH).
•
“polar” sets the polarity of the trigger
output. “Posit.” gives a +12V DC output
when the trigger is active and zero when
inactive. “Negat.” gives a +0V DC output
when the trigger is active and +12V
when inactive.
•
“delay” sets a delay between the “sense”
signal and the trigger output voltage
changing. The delay may be set to various
times from 1second to 3 minutes or to
“No” which give zero delay.
•
“durat.” Sets the period (duration) that
the trigger output is active. The trigger
duration may be set to various times from
10ms (milliseconds) to 3 minutes, or
to“Infin.” which keeps the trigger active
while the “sense” condition prevails.
•
EXIT returns to the main menu
Using the Myryad A-V Learning
Remote in CD mode.
To switch the remote into CD mode
press the CD “device” key at the top of
the handset. In CD mode many of the
keys still operate the MDP 500 functions
as described above. Only those whose
function changes to control Myryad CD
players are described below.
The CD Player keys carry out exactly the
same functions as the identically named keys
on the CD remote control handset supplied
with your Myryad CD Player. Some of the
keys on the CD handset controlling certain
infrequently used functions have been
omitted from the A-V Learning Remote
Control so that it is more straightforward to
use. All the other keys continue to control
the MDP 500 and operate exactly as
described in the previous section – with the
sole exception of the “7.1 CH / +10” key
which has no function in CD mode.
installing
and replacing
batteries
The remote handset uses four 1.5 V type
AAA batteries. To fit new batteries first
open the battery compartment in the rear
of the handset and remove any existing
batteries. Fit the new ones as directed by
the symbols printed inside the battery
compartment, then replace the battery
compartment cover. The batteries should
always be removed if they are discharged
(indicated by no remote control operation
or by operation only at very short range).
11
10
A-V Learning
Myryad CD
Remote key
function
POWER
STANDBY
CH
5
SKIP
4
CH
6
SKIP
3
5
/PAUSE
PAUSE
6
/STOP
STOP
3
/REW
SCAN
3
4
/FF
SCAN
4
SEL/PLAY
PLAY
PRE. CH/
6
0
(OPEN/CLOSE
(not all Myryad
CD players)
0,1,2,3,4,5,6,7,8,9
0,1,2,3,4,5,6,7,8,9
FAV
SHUFFLE
INFO
TIME
NEXT
REPEAT
trouble-shooting
guide
some of the most common problems
If a fault is detected switch the preamplifier
OFF immediately before checking or
changing cables or connections.
No sound:
•
Power turned OFF or power cord
disconnected. Check that the LED in
the STANDBY button is illuminated.
•
An inoperative input has been selected
(e.g. CD input with no CD playing or
TUNER input with the tuner switched off).
•
An input has been selected with no
source connected.
•
TAPE input has been selected with no
tape playing.
•
UK version only: The fuse in the mains
plug has failed. Check and replace if
necessary.
No sound in one channel only:
•
Interconnect cable pulled loose or making
poor contact. Check and, if necessary, un-
plug and re-plug all relevant cables.
Loud buzz or hum:
•
Interconnect cable pulled partially out
of its socket.
•
Defective interconnect cable.
Hum in tape playback
•
Tape deck too close to the power amplifier
(e.g. directly above or below).
•
Plugs making poor contact with sockets.
Incorrect operation
– some functions not working
•
Control processor latched. Switch off
POWER and wait for about one minute.
Then switch POWER on. Normal
operation should resume.
For further help please visit
www.myryad.co.uk/faqs.html
Display setup
TV system:
NTSC
Superimpose:
On
Temp. display:
Full
Video format:
Auto
OSD output:
Both
OSD style:
1
Exit
Table for recording new source names
Source number
Original source name
New source name
Remote control
Key name
Key no
1…………………………………………………………AUX 2 …………………………AUX 2 …………………………………3
2…………………………………………………………AUX 1 …………………………AUX 1 …………………………………2
3………………………………………………………………SAT ……………………………SAT …………………………………1
4 ……………………………………………………………VCR ……………………………VCR …………………………………6
5………………………………………………………………TV ………………………………TV …………………………………5
6 ……………………………………………………………DVD ……………………………DVD …………………………………4
7……………………………………………………………CD ………………………………CD …………………………………9
8 ………………………………………………………TUNER…………………………TUNER …………………………………8
Trigger setup
Trig
1
sense:
Power on
Trig
1
polar.:
Posit.
Trig
1
delay:
No
Trig
1
durat:
Infin.
Trig
2
sense:
DVD
Trig
2
polar.:
Posit.
Trig
2
delay:
1
s
Trig
2
durat:
30
s
Exit
specifications
All specifications ref. 1Vrms output
and 0dBf digital or 2Vrms analogue input,
except where stated.
Stereo analogue inputs
Input level ……………………………………………………………………………………………………………………………………………………2Vrms
Input impedance …………………………………………………………………………………………………………………………………17kΩ/100pF
Maximum input level (input sensitivity – 6dB)………………………………………………………………………………………………4Vrms
Stereo analogue outputs
(Tape REC and record outputs)
Output level …………………………………………………………………………………………………………………………2Vrms (same as input)
Output impedance………………………………………………………………………………………Tape Rec……………………………………500Ω
…………………………………………………………………………………………………………Record outputs ……………………………………60Ω
7.1
Channel analogue inputs
Input level ……………………………………………………………………………………………………………………………………………………1Vrms
Input impedance …………………………………………………………………………………………………………………………………17kΩ/100pF
Maximum input Levels …………………………………………………………………………………………………………………………………8Vrms
7.1
Channel line outputs
Output level …………………………………………………………………………………………………………………………………………………1Vrms
Output impedance ……………………………………………………………………………………………………………………………………………60Ω
Total harmonic distortion ……………………………………………………………………Stereo source …………………………………0.01%
……………………………………………………………………………………………………7.1 Channel source ………………………………0.003%
Signal-to-noise ratio (A weighted, analogue sources)………………………………Stereo source ……………………………………90dB
……………………………………………………………………………………………………7.1 Channel source ……………………………………95dB
Signal-to-noise ratio (A weighted, digital PCM source) ……………………………………………………………………………………100dB
Dimensions (width x height x depth) …………………………………………………………………………………………436 x 95 x 341mm
Weight, Net ………………………………………………………………………………………………………………………………………………………6kg
Voltage (automatic setting) ……………………………………………………………………………………………………………………100 to 240V
Stock No: OST0011890
Revision A
English MDP 500 ok 29/1/01 10:14 am Page 10