manualshive.com logo in svg

MyGate Q71B, Instruction Manual, Page: 2 / 25

Share
Download
MyGate Q71B Instruction Manual Download Page 2

 

The MyGate Q71B Control Board Installation Manual : Printed 06/11/2012 14:25 

2 

 

 
 

Contents 

Q71B control board layout ........................................................................................................................ 3

 

Pre-installation checks .............................................................................................................................. 4

 

Linking Essential Terminals ................................................................................................................... 5

 

Connecting the motors to the control board ............................................................................................... 6

 

Connecting the capacitors to the control board ......................................................................................... 6

 

Photocells ................................................................................................................................................. 7

 

Photocell positioning .............................................................................................................................. 7

 

Photocell Wiring .................................................................................................................................... 8

 

To Use in Closing Cycle ........................................................................................................................ 9

 

Connecting power to the control board .................................................................................................... 11

 

Programming the remote control / key-fob ................................................. 

Error! Bookmark not defined.

 

Saving a new remote controls / key-fobs to the control board ................. 

Error! Bookmark not defined.

 

Deleting existing remote controls / key-fobs from the control board ........ 

Error! Bookmark not defined.

 

Changing the code the key-fob transmits ............................................................................................. 13

 

Remote Control Receiver .................................................................................................................... 14

 

Extended Aerial 

– (optional accessory) ................................................................................................... 14

 

Fitting the Extended Aerial ................................................................................................................... 14

 

Selecting the Operating Mode ............................................................................................................. 15

 

Programming the gates open & closing cycles ........................................................................................ 16

 

Programming 

– Double Gates (for two leafs) ....................................................................................... 16

 

Setting the Pause Time ....................................................................................................................... 17

 

Obstacle Detection .............................................................................................................................. 17

 

Appendix: A ............................................................................................................................................ 20

 

Q71B connection map 

– terminals 1 to 21 ........................................................................................... 20

 

Appendix: D ............................................................................................................................................ 21

 

Q71B control board 

– FAQ’S ............................................................................................................... 21

 

Comments & Feedback ........................................................................................................................... 25

 

 

Summary of Contents for Q71B


























Reviews:

No comments