background image

3.

 

Operating Instructions 

The procedure of using TFPro with your tracking system: 

1). Detect the GPS baudrate. 

TFPro needs to recognize the GPS baudrate for the initial use. Please hold SetHome button 

and power on TFPro. 2 LEDs on TFPro will blink alternately. Once TFPro recognize the GPS the 2 
LEDs will stay solid on. After your GPS is recognized please power off the TFPro. You don’t need to 
do it any more unless you use a different GPS with TFPro. 

TFPro supports these baudrates: 9600,19200,38400,57600,115200bps. 
Default setting is 38400bps. 

2). Check the downlink status 

 

Power  on  the  plane  and  your  tracker.  If  everything works,  the  RX  LED  of AATDriver  should 

blink  very  fast.  AATDriver  V5  is  able  to  demodulate  tracking  data  from  Video  or  Audio  signal.   
We need to ensure that Video and Audio channels both are working.   
Please unplug the VideoRX video cable from the tracker. The Audio cable remains on the tracker. 
The RX LED should still blink (not so fast as before).   
Now  unplug  the  VideoRX  audio  cable  from  the  tracker.  The  Video  cable  remains.  The  RX  LED 
should blink fast. 
 

Press the SetHome button of TFPro for a few seconds. The tracker should “BEEP” while you 

holding the button. That means the tracker receives the SetHome command successfully. 

3). SetHome and take off 

The blinking RED led on TFPro indicates the GPS status. More satellites are locked, faster the 

LED  blinks.  The  RED  led will be  solid  on once  the GPS  locks  10  or  more  satellites.  And  it  won’t 
blink no GPS is detected. 
 

After we get enough satellites (usually we need 8 or more), press the SetHome button for 2 

seconds or longer until you hear the tracker Beeping.   
 

Now you can launch your plane. 
The tracker will start to track once the plane leaves 10 meters away. 

 
Other tips: 
 

1.Press the button on TFPro mainboard (beside the LEDs) to switch OSD mode circularly: 

 

 

PAL->Disable->NTSC-> Disable ->PAL-> Disable….. 

 

2.Hold the button on TFPro for 5 seconds or longer to reset all configuration. 

 

3.For the details about firmware update, please refer to the MFD AutoPilot manual. 

Summary of Contents for TeleFlyPro









Reviews: