EFLEX REMAPPING BUTTONS
R
Reflex remapping buttons are optional buttons or paddles on the back of the controller which can be assigned to a standard controller button. These buttons
can also be made turbo. See the programming mode instructions below for more information.
ROGRAMMING MODE
P
Within the programming mode you can setup the reflex buttons, change the rapid fire speed and change the burst fire shot amount.
Enter the programming mode:
HOLD R1 + R2 + L1 + L2 for 8 seconds, the white LED will make one long flash.
Exit the programming mode:
Tap L3
Change Rapid Fire Speed:
To change the rapid fire speed you only need to TAP
“UP”
or
“DOWN
” on the D-pad.
“UP”
to make the speed faster and
“DOWN
” to make it slower. The main
LED will flash GREEN when increasing the speed and RED when decreasing. Once you have reached the MIN or MAX speed the LED will no longer flash.
Change Burst Fire Quantity:
To change the number of shots fired with the burst fire you must TAP
“LEFT”
or
“RIGHT
” on the D-pad. Left for fewer shots and Right for More shots.
Check Rapid Fire Speed Setting:
To check the currently set rapid fire speed you only need to TAP
“TRIANGLE”
. The main LED will flash BLUE for the “tens” position and then flash GREEN for
the single digit. (example: BLUE flashes 3 times, followed by GREEN flashing 6 times, you are now at speed setting 36) Refer to the table below for all of the
speed setting options.
Check Burst Fire Setting:
To check the currently set burst fire setting just TAP
“X”
. The main LED will flash BLUE 2-10 times to indicate the number of shots set for the burst fire.
Reset Current Mode to Default Settings:
To reset the rapid fire mode you are currently editing to the factory default you must HOLD
“SQUARE”
and
“CIRCLE”
together for 7 seconds. After 7 seconds
the main LED will flash AQUA very fast 20 times to indicate the Mode has ben reset.
Change Reflex Button Mapping:
HOLD one of the Reflex buttons and TAP the button you want to assign to it. The main LED will flash GREEN 3 times to confirm your change. If you tap the
controller button which is already assigned to the reflex button, this will disable the button and the main LED will flash RED 3 times. The button will then not
do anything when pressed until it is reassigned to a new controller button.
Set Reflex Button to Turbo Speed:
Double tap the reflex button to cycle through the 5 speed settings listed below. The LED will flash 1-5 times to indicate the setting.
1. No Turbo 2. Turbo at the currently set rapid fire speed 3. Fixed 5sps turbo 4. Fixed 10sps turbo
5. Fixed 15sps turbo
HOLD ALL FOR 8 SECONDS
Rapid Fire Setting
Shots Per Second
Rapid Fire Setting
Shots Per Second
Rapid Fire Setting
Shots Per Second
1
50
18
16
35
9.5
2
45
19
15.4
36
9.3
3
40
20
14.8
37
9
4
36
21
14.3
38
8.7
5
33.33
22
13.8
39
8.5
6
30
23
13.33
40
8.33
7
28
24
12.9
41
8
8
26.67
25
12.5
42
7.7
9
25
26
12
43
7.5
10
23
27
11.75
44
7.3
11
22
28
11.5
45
7
12
21
29
11.1
46
6.67
13
20
30
10.8
47
6
14
19
31
10.5
48
5.5
15
18.2
32
10.25
49
5
16
17.4
33
10
50
4
17
16.67
34
9.75
