manualshive.com logo in svg

MuxLab 500435, Installation Manual, Page: 34 / 40

Share
Download
MuxLab 500435 Installation Manual Download Page 34

5x1 HDMI / HDBT Multimedia Presentation Switch 

Installation Guide

 

© MuxLab Inc. 2015 

34 

OSD Language

: Supports 7 languages, including English (default), Chinese etc. 

Restore Factory Default

: Restores to original system state. 

Blending

: Includes Low, Middle, High and Off. Use ENTER button to select. 

HDMI CEC

: Enable/disable CEC and auto-standby function. Default: CEC on, 

STANDBY on. Only when CEC is on, will it be able to set auto-standby status. 

OSD Duration

: can be set to 5 s, 10 s, 15 s and Off.    “s” is for Second. 

VERSION

: Displays software version. 

5.6 Instructions of VGA Converting Cable 

As VGA source supports YPbPr and Composite video source, the 500435 provides with 
2 VGA converting cables to comply with these signals. 

When you need to select these signals as input sources, please switch to channel 
INPUT 4 or INPUT 5, and then set the signal type in the OSD menu. Then switch to 
another input channel and connect INPUT 4 or INPUT 5 with corresponding source 
device. Finally, switch to INPUT4 or INPUT 5 again. 

Connect with Component Video (YPbPr) Source 

There are three different ways to connect a Component Video source: 

1.  From the front panel buttons & OSD 

Press the 

Menu

 button on the front panel to enter the OSD, and then enter the 

OPTION 

setting menu: set “INPUT 4 Select” to 

YPbPr1

, and “INPUT 5 Select” to 

YPbPr2

. Then, press 

Source/Auto

 button on the front panel to switch to YPbPr1 

or YPbPr2 source. 

2.  Via RS232 commands

 

Send command 

50681%

 (or 

50684%

) to switch to YPbPr1 (or YPbPr2) source. 

3.  Via IR remote & OSD

 

Press 

Menu

 button on IR remote to enter the OSD menu, then enter the 

OPTION 

setting menu: set “INPUT 4 Select” to 

YPbPr1

, and “INPUT 5 Select” to 

YPbPr2

. 

After setting, press 

INPUT 4

 (or 

INPUT 5

) button to switch to YPbPr1 (or YPbPr2) 

source. 

The VGA cable used to convert the VGA signal to Component Video looks like this: 

 

Summary of Contents for 500435









































Reviews:

No comments