manualshive.com logo in svg

MUTOH VJ-628 ValueJet, Operation Manual

Share
Download
MUTOH VJ-628 ValueJet Operation Manual Download Page 30

30     Pausing/Restarting printing

Pausing/Restarting printing

During printing, short press the operation key on the operation panel.

• The printing pauses.
• Press the operation key again to restart the printing.

Note

• In this operation, printing data sent to the product are not deleted.
• Please see the followings when canceling printing and deleting data.

"Canceling printing" on page 30

Canceling printing

Canceling printing from the operation panel

Press and hold the operation key on the operation panel for 2 seconds 

or more during printing.

• The printing is canceled (it cannot be restarted).
• The printing data sent to the product are deleted.

Canceling printing from printer driver/VSM

[1]

Display  the Printing Preferences screen of printer driver during printing.

"Displaying the Printing Preferences screen of printer driver" on page 8

[2]

Click [Cancel Printing] in the [Utility] tab under the [Utility] tab.

• The remote panel of VSM launches.
• The [Confirmation] window opens.

Note

• VSM can be launched directly.

"Launching VSM" on page 9

[3]

Click [Yes].

• The printing is canceled.

Press!

Press!

Summary of Contents for VJ-628 ValueJet

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands