MUTOH ValueJet VJ-1624WX Operation Manual Download | Manualshive

Page: 166 / 358

background image

4 Handling the printer

VJ-1624X/1624WX/1924WX OPERATION MANUAL

166

4.2 Media

4.2

Media

This section explains details of available media for this printer.

4.2.1

Media type

The type and quality of media greatly influence the print result.
Fully understand the following and use the media that matches the intended use.
The following media is recommended and available for this printer.
Select the appropriate media according to the intended use.

NOTE

• For details of the recommended media, contact your local MUTOH dealer.

• If failures or malfunctions of the printer occur by using the media other than the recommended

media:

• The printer will not be covered by the warranty and repair expenses will be covered by the

customer.

• For details, refer to the following.

5 Panel setup menu
7 Troubleshooting

• To request a repair, contact your local MUTOH dealer.

TIP

•When printing on media that is not recommended,

•Refer to the media manual or ask where you purchased the media for information on media types and appropriate settings

for this printer.

•Set the print quality according to

5.1.1 User Type menu

«
...
164
165
166
167
168
...
»

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1624WX

Pixma MG2400 Series

Brand: Canon Pages: 2

Brand: BadgePass Pages: 2

Brand: SPRT Pages: 28

Brand: F+D Feinwerk- und Drucktechnik Pages: 22

Brand: Xerox Pages: 3

Brand: Samsung Pages: 115

Brand: Canon Pages: 12

Brand: Oki Pages: 99

Brand: MF DIGITAL Pages: 2

MICROLINE ML310

Brand: Oki Pages: 32

Allen-Bradley ClearMark

Brand: Rockwell Automation Pages: 16

Brand: Oki Pages: 137

Brand: Jolimark Pages: 31

Brand: zortrax Pages: 8

imageCLASS LBP913w

Brand: Canon Pages: 327

Brand: Domino Pages: 114

Brand: DataCard Pages: 4

Pocket Photo PD239BH

Brand: LG Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands