background image

13

ENGLISH

THE POWER LED IS ON, BUT NO SOUND COMES FROM THE SPEAKERS
Check the following steps:
Low level mode: Are the RCA cables on the head unit and on the amplifier correctly connected?

•  The RCA cables are correctly connected.

Then an RCA cables could be defective. Check the function of the RCA cables on another audio 

device. If necessary, replace the defective RCA cables.

High level mode: Are the loudspeaker cables on the head unit and the high level inputs of the am-

plifier or on the high level cable plug correctly connected?

•  The speaker cables are connected correctly.

A speaker cable could be defective. If necessary, replace the speaker cable or insulate the damaged 

area.

Are the speaker cables correctly connected between the speakers or the subwoofer at the speaker 

outputs of the amplifier? 

•  The speaker cables are connected correctly.

A speaker cable could be defective. If necessary, replace the speaker cable or insulate the damaged 

area.

Is the high pass filter or subsonic filter set higher than the low pass filter on the amplifier?

Then slowly turn down the controller for the high pass filter or subsonic filter until the sound can be 

heard.

Is the input mode switch on the amplifier set correctly?

Check the setting and change the switch position if necessary.

Are the crossover switches on the amplifier set correctly?

Check the settings and change the respective switch position if necessary.

Are the speakers or the subwoofer working? 

Hold a standard 9 volt block battery to the terminals of each loudspeaker or the subwoofer.
•  A faint cracking sound can be heard.

The speaker or subwoofer is fine.

•  There is nothing to be heard.

The loudspeaker or subwoofer could be defective. If necessary, replace the defective speaker or 

subwoofer.

Are the settings on the head unit set correctly?

•  Check the fader and balance settings
•  Check whether the mute function is activated
•  Check whether a high pass or low pass filter is activated
•  Check whether playback has been paused
•  Check the source settings
•  Check whether any existing subwoofer output is activated

Summary of Contents for FOUR100

































Reviews: