manualshive.com logo in svg

Musicmakers BALLAD HARP KIT, Assembly Instructions Manual

Share
Download
Musicmakers BALLAD HARP KIT Assembly Instructions Manual Download Page 27

651-439-9120

27 

www.harpkit.com

NOTE: 

Wound harp strings are custom made for each model of harp. Some people break 

the first one they install by over-tightening. They don’t expect it to come up to pitch so 
quickly. Take care to avoid that costly mistake. It is very helpful to pluck the string as you 

tighten it, so you can hear the pitch go up as your increase the tension.

p

____1.

Start at the base (lowest) end of the harp. The lowest 4 strings of your harp are steel core with 
bronze wrap (SFB.) Push the string through the lowest hole inside the soundboard from the 
back to front. Pull it all the way until the knotted end contacts the back side of the soundboard.

WOUND STRINGS

INSTALLING STRINGS

____2. Thread the other end of the string through the corresponding tuning pin, pulling it through 

the pin. Clip the wire string  about 1-1/2” to 2” above the pin.  This leave enough slack in the 
string to allow 2-3 windings before coming taut. 

____3. Use the tuning wrench to turn the pin clock-

wise (from the viewpoint of the back of the 
tuning pin) and guide the windings neatly 
around the tuning pin. (fig. 3a)

____4. As the string begins to tighten, place it in the 

groove of the bridge pin. When you are satis-
fied with the installation of the string, use a 
wire cutter to clip off the excess tail, close to 
the tuning pin.

FIG. 3A

Nice

Windings!

____60. Finally you can install the strings! You will need a pair of scissors, a wire cutter, and your 

tuning wrench for this last operation, however, the messy part is over. So grab your favorite 
beverage and move to a comfortable spot in the house where you will turn this project into a 
musical instrument!

We have a nice video about how to install strings on your harp.  It would be worth watching 
that before you get started.  You’ll find that video along with some other useful information 
about harp strings here:

www.harpkit.com/blog/how-to-string-a-harp

Summary of Contents for BALLAD HARP KIT

































Reviews:

No comments

Brands by name

Popular brands

Load more brands