background image

Tri-Vista Power                       Instructions for Use   Page 9 of 9

SPECIFICATIONS :

Output voltage, RMS

92 Volts  20Hz to 20kHz

peak

130 Volts

Power output, single or both channels driven

1000 Watts per channel into 8 Ohms (24dBW)
1800 Watts per channel into 4 Ohms
3000 Watts per channel into 2 Ohms

Peak output current

± 200 Amps

Damping factor

205

Output devices per channel

40

Total Harmonic Dist noise

0

.

005% at 1kHz up to 80% power, into 8 Ohms

< 0

.

005% 20Hz to 20kHz at 12

.

5 Watts into 8 Ohms

Intermodulation distortion

0

.

002% at 12

.

5 Watts into 8 Ohms

Frequency response

20Hz to 20kHz ± 0dB
10Hz to  0 / -1dB

Audio gain

30dB (31

.

5 times) nominal

Input impedance

31K Ohm

Input sensitivity for full power output into 8 Ohms

2

.

92 Volts

Signal / noise ratio, reference full power output

> 124dB “A”- weighted

Input

1 RCA connector per monobloc

Outputs

2 monobloc channels via 3 pairs of speaker binding posts
per channel,

Power requirements

100 / 115 / 230V AC, 50 / 60Hz  (factory preset)
3000 Watts maximum with 8 Ohms load
160 Watts idle per channel

Dimensions

Main units

483 mm, 19 inches wide

318 mm, 12

.

5 inches high including feet

450 mm, 17

.

7 inches deep including terminals

Power supply

483 mm, 19 inches wide
168 mm, 6

.

6 inches high including feet

374 mm, 14

.

7 inches deep including sockets

Weight

Main units, each

43 kg,  94

.

8 lbs unit only, unboxed

61 kg,  135 lbs in shipping carton

Power supply

42

.

7 kg,  94

.

1 lbs unit only, unboxed

48

.

2 kg,  106 lbs in shipping carton

Standard

IEC mains leads - 16 Amp type 

:

two, 2

.

4 metres (94

.

5 inches) each

accessories

Switched mains interconnection leads 

:

two, 1

.

2 metres (47

.

3 inches), and 0

.

7 metres (27

.

5 inches)

Low voltage interconnection leads 

:

two, 1

.

2 metres (47

.

3 inches), and 0

.

7 metres (27

.

5 inches)

Control interconnection leads 

:

two, 1

.

2 metres (47

.

3 inches), and 0

.

7 metres (27

.

5 inches)

Loudspeaker leads 

:

two, twin conductors, 3 metres (118 inches) each

Issue 1:  March 2003

Musical Fidelity reserves the right to make improvements which may result in specification or feature changes without notice.

Tri-Vista

Power  Amplifier

Summary of Contents for Tri-Vista












Reviews: