background image

 

Issue 2                                             

 

 

Page 10 of

 

11 

SPECIFICATIONS

 

Output 

Power 

260 Watts per channel into 8 Ohms (24 dBW) 

Voltage 

46 Volts RMS, 20Hz to 20 kHz; onset of clipping 

 

(130 Volts peak-to-peak) 

 

Current peak-to-peak 

140 Amps 

Damping factor 

210 

Output devices  

4 pairs per channel 

 

Line input 

THD+N 

<0.007% typical, 20 Hz to 20 kHz 

Signal / noise ratio 

>120 dB ‘A’-weighted 

Input impedance 

50k Ohms 

Frequency response 

+0, –1dB, 10Hz to 100 kHz 

 

Connections 

Line level inputs 

1 pair line level XLR (balanced) connectors 

 

2 pairs line level RCA connectors 

Line level outputs 

1 pair line level RCA connectors 

 

Speaker outputs 

4 pairs 4mm banana plug/binding posts 

 

Power requirement 

Mains voltages 

115/230VAC 50/60Hz (factory pre-set) 

 

100VAC 50/60Hz (alternative) 

Consumption 

750 Watts maximum 

 

Weight 

Unit only, unboxed  

19.7 kg (43

 lbs) 

 

 

In shipping carton  

24.4 kg (53

 lbs) 

 

 

Dimensions 

Wide  

440 mm (17

 ”) 

 

High, including feet  

125 mm (5 ”)   

Deep (front to back) including terminals   390 mm (15

 ”) 

 

 

Standard accessories 

IEC type mains lead (10-Amp type) 
 
 

 

Musical Fidelity reserves the right to make improvements which may result in 

specification or feature changes without notice. 

 

 

Summary of Contents for M6PRX CRPS












Reviews: