manualshive.com logo in svg

Murray SELECT 309000x8NA, Safety, Assembly, Operating And Maintenance Instructions, Page: 29 / 52

Share
Download
Murray SELECT 309000x8NA Safety, Assembly, Operating And Maintenance Instructions Download Page 29

Level Adjustment

Position   

Figure 28

MAINTENANCE

29

F–030616C

HOW TO REMOVE THE MOWER HOUSING

1. Move the 

blade rotation control

 to the DISENGAGE position.

2. Move the 

lift lever

 to the level adjustment position (Figure 28).

NOTE: Make sure the lift lever

is locked in the LEVEL

ADJUSTMENT position.

3. Remove the hair pins and the

washers from the 

rear suspen-

sion arms

 (Figure 29). See il-

lustrations “C” and “D”.

4. Remove the hair pins and wash-

ers from the 

suspension links

.

See illustrations “A” and “B”.

5. Disconnect the 

extension spring

 from the 

blade control rod

.

See illustration “E”.

6. Disconnect the 

front hanger

 from the frame support. See

illustration “F”.

7. Remove the 

mower drive belt 

from the 

stack pulley

. See

illustration “G”.

8. Pull the mower housing away from the right side of the unit.
9. To operate without the mower housing, move the lift lever to the

TOP position.

HOW TO INSTALL THE MOWER HOUSING

1. Push the mower housing under the right side of the unit.
2. Put the

 mower drive belt 

around the 

stack pulley

. Make sure

the “V” side of the 

mower drive belt

 is against the 

stack pulley

.

Also, make sure the 

mower drive belt

 is not twisted.

3. Attach the 

front hanger

 to the frame support with the 

hanger

rod.

 Fasten with the fasteners as shown. See illustration “F”.

4. Make sure the 

mower drive belt

 is between the 

stack pulley

and the two 

belt guides

.

 

See illustration “G”.

5. Attach the 

suspension links

 to the 

lifter assembly

. Fasten

with the washers and hair pins. See illustrations “A” and “B”.

6. Attach the 

rear suspension arms

 to the suspension brackets.

Fasten with the washers and hair pins. See illustrations “C” and

“D”.

7. Attach the

 extension spring

 to the 

blade control rod

. See

illustration “E”.

8. Move the 

blade rotation control

 to the ENGAGE position.

Make sure the 

mower drive belt 

is inside all the 

belt guides

and is also below the 

spacer tube.

9. Make sure the mower housing is level. See the instructions on

“How To Level The Mower Housing”.

10. Check the operation of the 

blade rotation control

. See the in-

structions on “How To Adjust The Blade Rotation Control”.

Lifter 

Assembly

Blade Rotation

Control

Hanger Rod

Mower 

Drive Belt

Lift Lever

Figure 29

Extension

Spring

Suspension

Link

Adjuster

Arm

Adjuster

Arm

BeltGuide

Stack Pulley

Suspension

Link

BeltGuide

Front Hanger

Spacer Tube

Summary of Contents for SELECT 309000x8NA





















































Reviews:

No comments