Murray EV3850x4B Page 9 Operating Instructions Manual Download | Manualshive

Page: 9 / 24

background image

OPERATION

9

F–041104L

KNOW YOUR EDGER

READ THE OWNER’S MANUAL AND ALL SAFETY RULES BEFORE YOU OPERATE the

Edger. To familiarize yourself with the location of the controls, compare the illustrations with

your Edger.

Save this manual for future reference.

Depth Control Lever

Engine Stop

Lever

Fuel Tank

Cap

Blade Guard

Recoil

Starter

Handle

Control Rod

Blade Guide

Blade

Figure 6

Primer Button

Oil Fill Cap

Throttle Control

Air Filter

Index Lever

(Located On Left

Side Of Edger)

Throttle Control –

The engine is set to

run at full speed. The throttle control has
only two positions, RUN and STOP.

Primer Button –

Injects fuel directly into

the carburetor for faster starts.

Recoil Starter Handle –

The engine is

equipped with an easy pull recoil starter.

Index Lever –

Set bevel cut.

Depth Control Lever –

Controls depth of

cut.

Blade Guard –

Use to prevent stones and

debris from being thrown at the operator.

Engine Stop Lever –

Must be engaged

to allow the engine to start and run.

Release

to stop the engine.

«
...
7
8
9
10
11
...
»

Summary of Contents for EV3850x4B

























Reviews:

No comments

Related manuals for EV3850x4B

Brand: Echo Pages: 28

Brand: Yard Machines Pages: 20

Brand: Mantis Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands