manualshive.com logo in svg

Murray 309029 92B Series, Manual, Page: 31 / 52

Share
Download
Murray 309029 92B Series Manual Download Page 31

MAINTENANCE

31

F-030600L

HOW TO REPLACE THE MOWER DRIVE BELT

1.

Remove the mower housing. See the instructions on “How To
Remove The Mower Housing”.

2.

Pull the belt retainer away from the idler pulley and remove
the mower drive belt (Figure 31).

3.

Pull the brake pad away from the jackshaft pulley and remove
the mower drive belt.

NOTE: Replace the mower drive belt with an original
equipment belt from an authorized service center.

4.

Install the new mower drive belt. Pull the brake pad away
from the jackshaft pulley. Put the mower drive belt around
the jackshaft pulley.

5.

Pull the belt retainer away from the idler pulley. Put  the mow-
er drive belt around the idler pulley.

6.

Make sure the “V” side of the mower drive belt is against the
jackshaft pulley and the idler pulley.

7.

Install the mower housing. See the instructions on “How To
Install The Mower Housing”.

8.

Before you mow, check the blade rotation control. See the in-
structions on “How To Adjust The Blade Rotation Control”.

Figure 31

Mower Drive Belt

Belt Retainer

Brake Pad

Idler Pulley

Jackshaft Pulley

Summary of Contents for 309029 92B Series





















































Reviews:

No comments