Murray 198933 Instruction Book Download Page 9

9

OPERATION

KNOW YOUR LAWN MOWER

READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR 
LAWN MOWER.  Compare the illustrations with your lawn mower to familiarize yourself with 
the location of various controls and adjustments.  Save this manual for future reference.

MEETS CPSC SAFETY REQUIREMENTS

Sears rotary walk-behind power lawn mowers conform to the safety standards of the 
American National Standards Institute and the U.S. Consumer Product Safety Com-
 mis sion.  The blade turns when the engine is running.

Operator presence control bar – 

must 

be held down to the handle to start the 
engine.  Release to stop the engine.

Starter handle –

 used for starting engine.

These symbols may appear on your lawn mower or in literature supplied with the product. 
Learn and understand their meaning.

IMPORTANT:

  This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.

Primer –

 pumps additional fuel from the 

carburetor to the cylinder for use when 
starting a cold engine.

Starter 
handle

Gasoline fi ller cap

Spark plug

Engine oil cap with dipstick

Operator presence control bar

Primer

Muffl er

Discharge guard

Air fi lter

Housing

Summary of Contents for 198933



















Reviews: