Munters TRIO User And Installation Manual Download Page 163

Page: 163 / 206

163

Alarms

•

Defining the Alarm Parameters

•

Viewing the Alarms

•

Defining the Auxiliary Alarms

•

Sending a General Alarm

21.1

Defining the Alarm Parameters

1. Go to System > Control Strategy > Alarms

NOTE

Water Overflow, Water Shortage, and Potentiometer only appear if these devices are mapped.

Refer to Mapping Devices, page 50.

2. Click

3. Define:

•

Alarm delay: After detecting that a parameter has gone above or below its specs, TRIO waits
this amount of time before sending an alarm. This prevents sending alarms for short deviations.
Range: 0 – 999 seconds.

•

Alarm Reminder: TRIO will resend an alarm after this amount of time if the alarm is not
acknowledged. Range: 0 – 999 minutes.

•

Water Overflow Max Water/Hour: TRIO sends an alarm if the water flow exceeds this
amount.

Summary of Contents for TRIO















































































































































































































Search results

Summary of Contents for TRIO

Reviews:

Brands by name

Popular brands

Munters TRIO, User And Installation Manual

Search results

Summary of Contents for TRIO

Reviews:

Brands by name

Popular brands