Multitech MultiConnect Cell 100 Series MTC-EV3 User Manual Download

Page: 6 / 30

PRODUCT OVERVIEW

■

Devices that have a USB connector have the following LEDs:

■

Power

■

The tables that follow provide details about what the LEDs indicate.

Power

Not lit

DC power not present.

Lit

DC power present.

TR (Terminal Ready)

Not Lit

Data is not being transmitted.

Lit

Blinks when data is being transmitted.

CD (Carrier Detect)

Not lit

Data connection is not established.

Lit

Data connection is established.

LS (Link Status)

Not lit

There is no power to the cellular radio.

Continuously

Powered and connected, but not transmitting or receiving.

lit

Slow blink

Powered and searching for a connection.

Fast blink

Transmitting or receiving.

Side Panels

The device has connectors on either side. The figures that follow show the side panels.

MultiConnect

Cell 100 Series MTC-EV3 User Guide

Summary of Contents for MultiConnect Cell 100 Series MTC-EV3































Search results

Summary of Contents for MultiConnect Cell 100 Series MTC-EV3

Reviews:

Related manuals for MultiConnect Cell 100 Series MTC-EV3

Brands by name

Popular brands

Multitech MultiConnect Cell 100 Series MTC-EV3, User Manual

Search results

Summary of Contents for MultiConnect Cell 100 Series MTC-EV3

Reviews:

Related manuals for MultiConnect Cell 100 Series MTC-EV3

Brands by name

Popular brands